In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
Search Results "Clearance"
Filters
Commonly Searched Documents
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
-
Paperwork Reduction Act
This rule does not contain any paperwork or record keeping requirements and does not require clearance under the PRA....
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
Don-Jo Mfg., Inc. Pull Plate CFC7015
Number CFC7015 Dimensions 3-1/2" x 15" Ctc 6" Diameter 3/4" Projection 2-1/4" Clearance 1-...
-
Lavatories and Mirrors [4.19]
In those few toilet or bathrooms permitted to be adaptable, base cabinetry is allowed as long as required clear floor space and knee and toe clearances are available when the cabinet is...
-
M301.4 Lift Compatibility
An overhead lift (and possibly a gurney-based transfer) may be used in lieu of the provisions for clearances in or around the base of equipment to accommodate the legs of portable floor...
-
11B-604.8.1.2 Doors
Doors shall not swing into the clear floor space or clearance required for any fixture....
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
Forward Approach
Toe/knee clearance below the unit makes this reach easier by allowing a closer approach....
-
Notes:
Otherwise,, it is quite possible to configure a piece of equipment that meets all the clearances yet does not provide accessibility if there is not a defined method of measuring the clearances...
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
Bobrick ClassicSeries Surface Mounted Seat-Cover Dispenser B-221
Allow 5" (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection for filling dispenser from below unit....
-
R306.2 Pedestrian Signal Phase Timing
All pedestrian signal phase timing shall comply with section 4E.06 of the MUTCD (incorporated by reference, see R104.2) and shall be based on a pedestrian clearance time that is calculated...
-
11B-307.4.1 Guy braces
FIGURE 11B-307.4.1 GUY BRACES FIGURE 11B-307.4 VERTICAL CLEARANCE...
-
E2-3. Interior Stairs
., protected with a cane-detectable warning or a barrier that prevents travel into the area with less than an 80-inch-high head clearance)? [ADA Stds 4.4.2] Yes _____ No _____...
-
16(a)(v)
(v) The accessible rooms for individuals with mobility disabilities have the maneuvering clearances for beds specified in ADA Standards §9.2.2(1), to and within the bathroom (ADA Standards...
-
Don-Jo Mfg., Inc. Pull Plate 7011
Number 7011 Dimensions 3-1/2" x 15" Ansi J405 Ctc 5-1/2" Diameter 5/8" Projection 2" Clearance...
-
Bobrick MatrixSeries Seat-Cover Dispenser B-5221
Allow 5" (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection for filling dispenser from below unit....
-
4.2.5* Forward Reach
If the high forward reach is over an obstruction, reach and clearances shall be as shown in Fig. 5(b)....
-
4.34.5.3 LAVATORY, MIRRORS, AND MEDICINE CABINETS
(2) If a cabinet is provided under the lavatory in adaptable bathrooms, then it shall be removable to provide the clearances specified in 4.22.6....
-
Are doors or gates to employee work areas required to comply?
Entry doors or gates to employee work areas are required to meet applicable requirements, including those for maneuvering clearance, on the exterior, but not the interior....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
1.17 Unobstructed view
purposes of this Consent Order, shall mean and refer to a view to the screen that is not blocked or interfered with by any seats, railings, or other objects and is configured to have visual clearance...
