Powder coated steel partitions provide high-tech quality at an economical price. The powder coated finish is electrostatically applied over galvannealed steel, which protects against...
Search Results "Recessed Toilet Paper Dispenser"
Filters
Commonly Searched Documents
-
ASI Global Partitions Powder Coated Steel Partitions
-
4.1.6(3)(e)(ii)
(ii) Where it is technically infeasible to install a required standard stall (Fig. 30(a)), or where other codes prohibit reduction of the fixture count (i.e., removal of a water...
-
5.3.2.3 Slope
The slope of the turning space and clear floor or ground space surface shall not be steeper than 1:48 (2 percent) in all directions. Exception: When the surface is not paved or is...
-
§ 35.151(b)(4)(iii)(B)
(B) Costs that may be counted as expenditures required to provide an accessible path of travel may include:
-
§ 38.107(a)(4)
(4) Faucets and flush controls shall be operable with one hand and shall not require tight grasping, pinching, or twisting of the wrist. The force required to activate controls shall...
-
§ 38.123(a)(5)
(5) Doorways on the end of the enclosure, opposite the water closet, shall have a minimum clear opening width of 32 inches. Doorways on the side wall shall have a minimum clear...
-
11B-809.10.7.5 Controls
Controls shall be mounted 44 inches (1118 mm) maximum above the finish floor. The force required to activate controls shall be 5 pounds (22.2 mm) maximum.
-
11B-805 Medical care and long-term care facilities
Toilet rooms that are accessed from an examination, diagnostic or treatment room shall also be accessible....
-
Sales and Service Elements and Spaces
[See subsections ...]
-
Michael Graves at TEDMED 2011
Following a stay in a rehab center, the architect realized that most hospitals ignore critical resident needs. He set out to change all that with attractive, efficient,...
-
Case: ADA Standard Section 703.5.2
Characters shall be uppercase or lowercase or a combination of both.
-
Designations: ADA Standard Section 216.2
Section 216.2 covers scoping requirements in the current ADA Standards for sign designations.
-
11B-216.2 Designations
Interior and exterior signs identifying permanent rooms and spaces shall comply with Sections 11B-703.1, 11B-703.2, 11B-703.3, and 11B-703.5. Where pictograms are provided as...
-
11B-703.5.2 Case
Characters shall be uppercase or lowercase or a combination of both.
-
11B-703.1.1 Plan review and inspection
Signs as specified in Section 11B-703, or in other sections of this code, when included in the construction of new buildings or facilities, or when included, altered or replaced due...
-
Rockwood Manufacturing Company BF687 BF Series Men's ADA Toilet Room Sign
Material: .125" Non-Glare Plastic or .050" Thick Brass, Bronze Plastic Signs: Available in black, blue, brown, or red with standard 1" white lettering. Metal Signs: Available...
-
Rockwood Manufacturing Company BF688 BF Series Women's ADA Toilet Room Sign
Material: .125" Non-Glare Plastic or .050" Thick Brass, Bronze Plastic Signs: Available in black, blue, brown, or red with standard 1" white lettering. Metal Signs: Available...
-
Rockwood Manufacturing Company BF689 BF Series Unisex ADA Toilet Room Sign
Material: .125" Non-Glare Plastic or .050" Thick Brass, Bronze Plastic Signs: Available in black, blue, brown, or red with standard 1" white lettering. Metal Signs: Available...
-
11B-604.7.2 Disposal units
Sanitary napkin disposal units, if provided, shall comply with Section 11B-309.4 and shall be wall mounted and located on the sidewall between the rear wall of the toilet and the toilet...
-
This is a great unit but it's not "recessed", it's semi-recessed.
Having the additional volume helps to minimize housekeeping trips for overflowing waste receptacles, but the designer must keep the 4" projection in mind when laying out the toilet room....
-
11B-604.7.2 Disposal units
Sanitary napkin disposal units, if provided, shall comply with Section 11B-309.4 and shall be wall mounted and located on the sidewall between the rear wall of the toilet and the toilet...
-
Sec.36.403(f) Disproportionality
(f) Disproportionality.
-
F216 Signs
[See subsections ...]
-
703.4.1 Height above Finish Floor or Ground
Tactile characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60...
