EVCS complying with Section 11B-812 that serve a particular building or facility shall be located on an accessible route to an entrance complying with Section 11B-206.4. Where EVCS...
Search Results "Vehicle Ramp"
Commonly Searched Documents
-
11B-812.5.1 Accessible route to building or facility
-
§ 38.159(b)(1) Design load
(1) Design load. The design load of the lift shall be at least 600 pounds (2665 N). Working parts, such as cables, pulleys, and shafts, which can be expected to wear, and upon which...
-
11B-228.3.1.1 Existing facilities
Where new EVCS are added to a facility with existing EVCS, the requirements of Section 11B-812 shall apply only to the new EVCS installed. Alterations to existing EVCS shall comply...
-
11B-228.3.1.1 Existing facilities
Where new EVCS are added to a facility with existing EVCS, the requirements of Section 11B-812 shall apply only to the new EVCS installed. Alterations to existing EVCS shall comply...
-
11B-812.5.1 Accessible route to building or facility
EVCS complying with Section 11B-812 that serve a particular building or facility shall be located on an accessible route to an entrance complying with Section 11B-206.4. Where EVCS...
- SafePath: Overview of Ramps and Reducers for ADA Compliance by SafePath Products
-
3. Exception to Ramp Running Slope
A ramp in the built environment to which this exception applies may use a 1:2 grade slope on a short rise ramp....
-
1015.3 Height
On ramps and ramped aisles, from the ramp surface at the guard....
-
§ 38.125(c)(1) Design load
Ramps or bridge plates 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp or bridge plate distributed over an area of 26 inches by 26 inches, with...
-
Governmental Units Affected (R208 Detectable Warning Surfaces) (Section-by-Section Analysis)
The Access Board seeks information on whether any state and local transportation departments currently use UFAS for curb ramps in the public right-of-way....
- Guidance for Conducting Physical Functional Assessments for ADA Paratransit Eligibility
- CalCasp Training: 2016 California Building Code Chapter 11B
-
Portable ramp - greater than six inch step
[See subsections ...]
-
R304.5.3 Cross Slope
The cross slope of curb ramps, blended transitions, and turning spaces shall be 2 percent maximum....
-
§ 38.125(c)(7) Stowage
A compartment, securement system, or other appropriate method shall be provided to ensure that stowed ramps or bridge plates, including portable ramps or bridge plates stowed in the passenger...
-
§ 38.93(d)(3) Exception
horizontal gap or vertical alignment specified in paragraph (d)(1) or (d)(2) of this section, car, platform or portable lifts complying with §38.95(b) of this part, or car or platform ramps...
-
1015.2 Where required
Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms, aisles, stairs, ramps and landings that are located more than 30 inches (762 mm) measured...
-
§ 38.95(a)(2) Exception
If level-entry boarding, portable or platform lifts, ramps or bridge plates meeting the applicable requirements of this section are provided on station platforms or other stops required...
-
R407.6.1 Slope
R407.6.1 Slope. Landing slopes shall be 2 percent maximum in any direction.
-
1013.3 Height
On ramps, from the ramp surface at the guard. Exceptions: 1. ...
-
1013.2 Where required
Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms, stairs, ramps and landings that are located more than 30 inches (762 mm) measured vertically...
-
1015.2 Where required
Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms, aisles, stairs, ramps and landings that are located more than 30 inches (762 mm) measured...
-
T103 Definitions
transportation vehicles....
-
§ 38.57(b)
(b) Handrails, stanchions, and seats shall allow a route at least 32 inches wide so that at least two wheelchair or mobility aid users can enter the vehicle and position the wheelchairs...