Handrail gripping surfaces shall have a cross section complying with Section 11B-505.7.1 or 11B-505.7.2.
Search Results "Vehicle Ramp"
Commonly Searched Documents
-
11B-505.7 Cross section
-
11B-235.1 General
Recreational boating facilities shall comply with Section 11B-235.
-
Passenger Loading Zones
The 1991 Standards and the 2010 Standards both include technical requirements for the vehicle pull-up space (96 inches wide minimum and 20 feet long minimum)....
-
T504 Fare Collection Devices
Section T504 in the 2016 Non-Rail Vehicle Guidelines establishes specifications for the location of fare collection devices (to ensure that such devices do not impede wheelchair movement...
-
Are the elements of path of travel and accessible routes substantively the same (such as slope, vertical clearance, width of path of travel, etc.)?
EVCS required by CBC Chapter 11B to be accessible must have an accessible route to the facility entrance (see CBC Section 11B-812.5.1) and an accessible route from the vehicle space to the...
-
How are accessible passenger loading zone aisles to be marked?
Vehicle pull-up spaces are not required to be marked....
-
T304 Operable Parts
The technical requirements for operable parts in the 2016 Non-Rail Vehicle Guidelines remain the same as in the proposed rule; however, they have been slightly reorganized so that all requirements...
-
Q14: Application of Section 504 Safe Harbor to Curb Ramps Built in Compliance with 1991 ADAAG
Q14: Does the Section 504 safe harbor apply to curb ramps built in compliance with 1991 ADAAG during the time period when the requirement for detectable warnings was suspended and the roadway...
-
12 [§ 4.7.9]
12 [§ 4.7.9] When a curb ramp is located at a marked crossing, the area where the ramp run ends must be contained within the marked crossing....
-
Sidewalks and Walkways
Some sidewalks do not include curb ramps or, if they do, the ramped section is too narrow or steep....
- SafePath: Overview of Ramps and Reducers for ADA Compliance by SafePath Products
-
1132A.4, Item 4
., concrete, brick, flagstone) may have a maximum change in height from the interior landing of 1 inch (25.4 mm), provided a ramp with a maximum slope of 1:8 is permanently installed....
-
1015.3 Height
On ramps and ramped aisles, from the ramp surface at the guard....
-
R207.1 General
A curb ramp, blended transition, or a combination of curb ramps and blended transitions complying with R304 shall connect the pedestrian access routes at each pedestrian street crossing....
-
Problem Two (Accessible Route)
Problem Two: The accessible route crosses a curb and no curb ramp is provided. Solution: Install a portable ramp....
- Guidance for Conducting Physical Functional Assessments for ADA Paratransit Eligibility
- CalCasp Training: 2016 California Building Code Chapter 11B
-
What is the Minimum Width for Non-Level Boarding?
[49 CFR §§ 37.9, 37.41-37.43, 38.125] June 16, 2015
-
3. Exception to Ramp Running Slope
A ramp in the built environment to which this exception applies may use a 1:2 grade slope on a short rise ramp....
-
§ 38.93(d)(4) Exception
Retrofitted vehicles shall be coordinated with the platform in new and key stations such that the horizontal gap shall be no greater than 4 inches and the height of the vehicle floor, under...
-
§ 38.125(c)(1) Design load
Ramps or bridge plates 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp or bridge plate distributed over an area of 26 inches by 26 inches, with...
-
1015.3 Height
On ramps and ramped aisles, from the ramp surface at the guard....
-
Governmental Units Affected (R208 Detectable Warning Surfaces) (Section-by-Section Analysis)
The Access Board seeks information on whether any state and local transportation departments currently use UFAS for curb ramps in the public right-of-way....
-
C. Chapter 2: Scoping Requirements
Chapter 2 in the 2016 Non-Rail Vehicle Guidelines has been substantially reorganized to present a more simplified approach....
