A landing with a minimum length of 48 inches will provide sufficient turning space....
Search Results "Counter Length"
-
Obstructions [4.7.8]
-
Trailhead Signs
information signs are provided at trailheads on newly constructed or altered trails designed for use by hikers or pedestrians, the final rule requires the signs to include information on the length...
-
4.4.4 Clear Floor or Ground Space
The long dimension of the clear space shall be roughly perpendicular to the length of the bench....
-
The SmartWheel
The SmartWheel is a wheelchair - mounted device for measuring propulsion parameters that can be used to compute forces, acceleration, rate of rise, velocity, stroke length, and other aspects...
-
Features of Accessible Parking Spaces for Cars
Access aisle of at least 60-inch width must be level (1:50 maximum slope in all directions), be the same length as the adjacent parking space(s) it serves and must connect to an accessible...
-
1003.3.1 Boat Slip Clearance
Clear pier space shall be permitted to be 36 inches (915 mm) wide minimum for a length of 24 inches (610 mm) maximum, provided that multiple 36 inch (915 mm) wide segments are separated...
-
1. Transfer Supports
In the preamble to the MDE NPRM, the Access Board posed multiple questions about whether the final rule should include more specific requirements regarding location, length, size, height...
-
T103 Definitions
“Large non-rail vehicles” are vehicles more than 25 feet in length, as measured from standard bumper to standard bumper, and “small non-rail vehicles” are vehicles equal to or less than...
-
MAKING THE BUILT ENVIRONMENT ACCESSIBLE
no access aisle to allow deployment of a van’s wheelchair lift, steps at a facility’s entrance or within its serving or selling space, aisles too narrow to accommodate mobility devices, counters...
-
Common Requirements (R304.5) (Section-by-Section Analysis)
A maximum counter slope of 5 percent is specified for the gutter or street at the foot of curb ramp runs, blended transitions, and turning spaces....
-
20. DESIGN AND CONSTRUCTION STANDARDS
., signage, front desk counter) for any Brand, it shall ensure that such designs comply with the ADA Standards....
-
Landscape Forms Inc. Scarborough Bench Collection
., 72in. or 96in. lengths. Backless bench in 48in., 72in. or 96in. lengths. Horizontal strap or woven metal seat....
-
Omnia Industries Inc. Interior Modern Lever Latchset - Stainless Steel No.47
Interior Modern Lever Latchset - Stainless Steel Dimensions: 3" Projection x 5- 1/2 " Length, 11/16" Lever Diameter Finishes: US32D...
-
604.5.2 Rear Wall
The rear grab bar shall be permitted to be 24 inches (610 mm) long minimum, centered on the water closet, where wall space does not permit a length of 36 inches (915 mm) minimum due to the...
-
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment
A positioning support will extend horizontally along the side of the patient scanning/imaging bed/table and be 12 - 16 inches in length and 3 - 6 inches above the transfer surface....
-
7.2.2.1 Determining Impracticability
One or more conditions for an exception exist that result in significant deviations from the technical provisions of section 7.4.1 through 7.4.8 for over 15 percent of the length of the...
-
Parking Spaces [4.6.3]
The length of accessible spaces is not specified. Access aisles must be as long as the parking space....
-
4.21.2 Size and Clearances
guidelines for roll-in shower stalls are based on residential size fixtures (30" x 60" minimum or the space used by a standard residential tub/shower unit) and spaces (30" minimum depth by the length...
-
4.20.2 Floor Space
The amount of clear floor space in front of a bathtub required by ADAAG (30"-48" min depth depending on the direction of travel by the length of the tub including a seat at the head of the...
-
Slope [§405.2] and Cross Slope [§405.3]
Slope [§405.2] and Cross Slope [§405.3] Slope represents the proportion of vertical rise to horizontal length and is specified in the Standards as a ratio (e.g., 1:12)....
-
EFFECTIVE COMMUNICATION DURING FACE-TO-FACE SERVICES
The determination shall take into account the nature, circumstances, length, complexity, and importance of the communication, as well as the communication skills of the person with a disability...
-
11B-1003.3.1 Boat slip clearance
Clear pier space shall be permitted to be 36 inches (914 mm) wide minimum for a length of 24 inches (610 mm) maximum, provided that multiple 36 inch (914 mm) wide segments are separated...
-
5.4.4 Transfer Support Distance from Transfer Surface Recommendations for M301 and M302
The transfer support would extend horizontally the entire depth of the transfer surface and would be 15 inches minimum in length....
-
1003.3.1 Boat Slip Clearance
Clear pier space shall be permitted to be 36 inches (915 mm) wide minimum for a length of 24 inches (610 mm) maximum, provided that multiple 36 inch (915 mm) wide segments are separated...
