Demonstrated by data showing that the selection procedure measures the degree to which candidates have identifiable characteristics which have been determined to be important for successful...
Search Results "Tape Measure"
Filters
Commonly Searched Documents
-
§1607.16 Definitions.
-
Introduction
Dimension definitions and measurement techniques vary from study to study and, in many cases, samples were very small....
-
POLLING PLACE ACCESSIBILITY IS REQUIRED BY THE AMERICANS WITH DISABILITIES ACT
Because a mix of public and private facilities are used as polling places, public entities may ensure Election Day accessibility of a polling place by using low-cost temporary measures,...
-
AJW Architectural Products U115 32 oz. Stainless Steel Powder Soap Dispenser - Surface Mounted
Pre-measured amounts of powder soap are dispensed to prevent waste and is moisture resistant to avoid caking of powder....
-
Just Manufacturing Classroom Concealed Ledgemount Teardrop Handle Faucet
Classroom faucets feature rigid spouts, or restricted swing spouts, providing preventative measures against wet counter tops in the classroom....
-
AJW Architectural Products U116 16 oz. ABS Liquid Soap Dispenser - Surface Mounted
Valve is located above fluid level to assure a drip free operation and dispenses a pre-measured amount of soap to prevent waste. Housing: Fabricated of chrome plated brass....
-
Just Manufacturing Concealed Classroom Faucet with Triple Radius Spout
Classroom faucets feature rigid spouts, or restricted swing spouts, providing preventative measures against wet counter tops in the classroom....
-
Sears Brands, LLC Craftsman 10 in. Digital LaserTrac® Level
Digital LaserTrac Level recalls last 9 measurements, calculates degrees between two angles, projects bright red laser dot accurately to 1/4 in. at 100 feet....
-
1. If a test screens out or tends to screen out an individual with a disability or a class of such individuals on the basis of disability, it must be job-related and consistent with business necessity
A test will most likely be an accurate predictor of the job performance of a person with a disability when it most directly or closely measures actual skills and ability needed to do a job...
-
II. Overview of Requirements
Public accommodations must -- Provide goods and services in an integrated setting, unless separate or different measures are necessary to ensure equal opportunity. ...
-
Addendum A: List of Terms
Wheelchair seat height- The distance measured from the floor to the top of the wheelchair seat cushion. This distance is measured at the center of the seat....
-
4.3.5.2 180-degree turn
Findings from the Anthropometry of Wheeled Mobility Study indicate that a width of at least 130 cm (51 in.) was required for 50% of the manual wheelchair users measured in this study to...
-
The ADA Standards for Accessible Design (the ADA Standards)
The ADA Standards identify what features need to be accessible, set forth the number of those features that need to be made accessible, and then provide the specific measurements, dimensions...
-
11B-308.3.1 Unobstructed
Operable parts of fuel dispensers shall be permitted to be 54 inches (1372 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs...
-
M302.2.1 Adjustability (Section-by-Section Analysis)
high transfer position of 25 inches; (3) at least four additional transfer positions located between the low and high transfer positions and separated by one inch minimum increments; (4) measured...
-
407.2.2.3 Audible Signals
The audible signal and verbal annunciator shall be 10 dB minimum above ambient, but shall not exceed 80 dB, measured at the hall call button. EXCEPTIONS: 1....
-
407.2.2.3 Audible Signals
The audible signal and verbal annunciator shall be 10 dB minimum above ambient, but shall not exceed 80 dB, measured at the hall call button. EXCEPTIONS: 1....
-
2.5.2.2 International Organization for Standardization (ISO) Standards
The risk mitigation measures must also be assessed to confirm their effectiveness at reducing the risks to acceptable levels and to ensure that they did not introduce any new hazards or...
-
Supporting Documents for the Medical Diagnostic Equipment Accessibility Standards Advisory Committee Report
Subcommittee Report - Weight Scales IDeA Center Memo – Transfer Surface Dimensions IDeA Center Memo - Mammography Knee Clearance Depth and Footrest Clearance IDeA Center Memo - Wheelbase Measurements...
-
Is a transportation operator required to procure vehicles with lifts that have a design load of more than 600 pounds?
No. 49 CFR Part 38 continues to require that lifts have a minimum design load of 600 pounds and that the lift platform accommodate a wheelchair measuring 30 inches by 48 inches....
-
Is a transportation operator required to procure vehicles with lifts that have a design load of more than 600 pounds?
No. 49 CFR Part 38 continues to require that lifts have a minimum design load of 600 pounds and that the lift platform accommodate a wheelchair measuring 30 inches by 48 inches....
-
If the Passenger Poses a Direct Threat to the Health and Safety of Others
that person to provide a medical certificate stating that the disease at its current stage would not be transmittable during the normal course of a flight or, if applicable, describing measures...
-
11B-411.2.1.2.3 Accessibility function button
The dots shall be spaced ¼ inch (6.4 mm), measured center to center, in the form of an equilateral triangle with a vertex pointing up. ...
-
11B-411.2.2.2 Verbal identification
Auditory volume shall be at least 10 dB above ambient sound level, but shall not exceed 80 dB, measured 36 inches (914 mm) in front of the elevator entrance and at 48 inches (1219 mm) above...
