TSPP Push and Pull is made from 16 gage stainless steel. Many different sizes to choose....
Search Results "Push Side"
-
TownSteel THPP Push and Pull Plate
-
Hager Companies Push/Pull Latch 311H
Hager Push/Pull Latch 311H: - New design replacing 311D - Engraving is available (optional) - Non-handed - Hospital latch Standard Materials: - Zinc and stainless...
-
g-iii
Is there clear maneuvering floor space in front of each accessible door (see ADA Standards § Fig. 25) and, on the pull side, is there at least 18 inches clear floor space beyond the latch...
-
Hager Companies Push/Pull Latch 311L
Hager Push/Pull Latch 311L: - Engraving available (optional) - Lead lined - Non-handed - Hospital Latch - 311L is same as 311H but for use on lead lined doors - *Horizontal...
-
604.5.1 Side Wall
The side wall grab bar shall be 42 inches (1065 mm) long minimum, located 12 inches (305 mm) maximum from the rear wall and extending 54 inches (1370 mm) minimum from the rear wall. ...
-
BEA Inc. PBR45 Series Door Access 4.5" Round Push Plate (Push to Open)
The PR 4.5 series is BEA's smallest, most discreet push plate line, smaller than the 4.75 and 6 inch push plates. ...
-
407.12.2.2 Obstructed Side Reach (Section-by-Section Analysis)
407.12.2.2 Obstructed Side Reach (Section-by-Section Analysis) This section proposes that, where the operable part is located more than 10 inches, but not more than 24 inches, behind...
-
M4
On the latch, pull side of the door, is there at least 18 inches clearance provided if the door is not automatic or power operated?...
-
Curb Ramps
Error/Omission: Curb ramp that is located across a circulation path has steep unprotected side flares. Result: People walking across the curb ramp may trip and be injured....
-
5.3.2.2 Transfer Sides for Imaging Equipment
5.3.2.2 Transfer Sides for Imaging Equipment. The transfer surface should be provided on at least one long side of the table....
-
M302.2.3 Transfer Sides
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface....
-
604.5.1 Side Wall
The side wall grab bar shall be 42 inches (1065 mm) long minimum, located 12 inches (305 mm) maximum from the rear wall and extending 54 inches (1370 mm) minimum from the rear wall....
-
604.5.1 Side Wall
The side wall grab bar shall be 42 inches (1065 mm) long minimum, located 12 inches (305 mm) maximum from the rear wall and extending 54 inches (1370 mm) minimum from the rear wall....
-
11B-604.8.1.1.2 Maneuvering space with side-opening door
11B-604.8.1.1.2 Maneuvering space with side-opening door....
-
3.3.15.3 Side (lateral) reach – over an obstruction depth of 610 mm
3.3.15.3 Side (lateral) reach – over an obstruction depth of 610 mm The vast majority of WhMD users in our study that displayed some reach capability could not reach at or beyond a 610...
-
11B-604.8.1.1.2 Maneuvering space with side-opening door
In a wheelchair accessible compartment with a door located in the side wall or partition, either in-swinging or out-swinging, a minimum 60 inches (1524 mm) wide and 60 inches (1524 mm) deep...
-
404.2.4 Maneuvering Clearances
Maneuvering clearances shall extend the full width of the doorway and the required latch side or hinge side clearance....
-
Locating Controls & Devices: Percent of People Who Can Reach the Matrix Cell Indicated While Holding No Weight - Side Approach Power Chair
These data depict the reaching abilities of power chair users represented as the percentage of users expected to reach to a target location in the lateral or sideways reach...
-
Locating Controls & Devices: Percent of People Who Can Reach the Matrix Cell Indicated While Holding No Weight - Side Approach Manual Wheelchair
These data depict the reaching abilities of manual chair users represented as the percentage of users expected to reach to a target location in the lateral or sideways reach...
-
404.2.4 Maneuvering Clearances
Maneuvering clearances shall extend the full width of the doorway and the required latch side or hinge side clearance....
-
404.2.4 Maneuvering Clearances
Maneuvering clearances shall extend the full width of the doorway and the required latch side or hinge side clearance....
-
407.8.2.2 Obstructed Side Reach
Where the operable part is located more than 10 inches (255 mm), but not more than 24 inches (610 mm), beyond the vertical reference plane, the height of the operable part shall be...
-
407.12.2.2 Obstructed Side Reach
Where the operable part is located more than 10 inches (255 mm), but not more than 24 inches (610 mm), beyond the vertical reference plane, the height of the operable part shall be...
-
BEA Inc. PBS45 Series Door Access 4.5" Square Push Plate (Push to Open)
The PBR 4.5 series is a smaller solution to the standard 6 inch PR series push plates....
