The MDE NPRM proposed to require diagnostic equipment used by patients seated in a wheelchair which has components that are used to examine specific body parts, be capable of examining those...
Search Results "Seat Location"
-
M303.4 Components (Section-by-Section Analysis)
-
5.3.3.1 Transfer Sides for Exam Chairs with Fixed Footrests
The 17 inch minimum depth and 21 inch minimum width should be located on both sides of examination chairs with a fixed footrest to allow for a left or right transfer....
-
TOTO® MS854114EL Commercial Eco UltraMax One-Piece Toilet ADA Height
Comes with SoftClose seat or optional Washlet upgrade....
-
Figure 608.5.3 Alternate Roll-In Type Shower Compartment Control Location – Drawing from the U.S. Access Board
-
Wall furr-out to support a grab bar when toilet is too far from the side wall
Here's a good example of one solution for a water closet that's too far from the adjacent side wall. Sometimes this solution is easier than moving the fixture when an offset flange...
-
11B-604.9 Water closets and toilet compartments for children's use
SECTION TITLE NOTES 11B-604.9 Water closets and toilet compartments for children's...
-
7. Amend 28 CFR part 35 by adding § 35.138 to read as follows:
7. Amend 28 CFR part 35 by adding § 35.138 to read as follows:
-
§ 35.138 Ticketing
§ 35.138 Ticketing.
-
4.1 Wheeled Mobility Device Dimensions
The height of the seat can be measured at the edge and at the middle, under the cushion, or on top of the cushion....
-
M302.2.3 Transfer Sides
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface....
-
5.8.1 Wheelchair Spaces on Raised Platforms Recommendations
5.8.1 Wheelchair Spaces on Raised Platforms Recommendations Description: Proposed section M303 provides technical criteria for diagnostic equipment used by patients seated in a wheelchair...
-
M303.1 General
Diagnostic equipment used by patients seated in a wheelchair shall comply with M303....
-
M303.1 General
Diagnostic equipment used by patients seated in a wheelchair shall comply with M303....
-
F202.6.5.5 Assembly Areas
Assistive listening systems shall comply with F219 and assembly seating shall comply with F221....
-
F206.2.4 Spaces and Elements
In assembly areas with fixed seating required to comply with F221, an accessible route shall not be required to serve fixed seating where wheelchair spaces required to be on an accessible...
-
206.2.4 Spaces and Elements
In assembly areas with fixed seating required to comply with 221, an accessible route shall not be required to serve fixed seating where wheelchair spaces required to be on an accessible...
-
M303.4 Components
Where components of diagnostic equipment are used to examine specific body parts, the components shall be capable of examining the body parts of a patient seated in a wheelchair....
-
M303.4 Components
Where components of diagnostic equipment are used to examine specific body parts, the components shall be capable of examining the body parts of a patient seated in a wheelchair....
-
Whitehall Mfg. WH2142W2 Ligature-Resistant Toilet Wall Supply On-Floor Wall Waste
On-Floor/Wall Waste: Available as Option Wall Supply: Available as Option Ligature Resistant: Yes Appropriate for: Ligature Resistant Waste Location...
-
M303.2.3 Wheelchair Spaces / Depth of Wheelchair Spaces for front or Rear Entry
For example, the wheelchair footrests would be allowed to extend beyond the depth of the raised platform and over any edge protection on wheelchair weight scales used by patients seated...
-
M302.2.3 Size
Transfer surfaces shall be 21 inches (610 mm) wide minimum and 17 inches (430 mm) deep minimum. The size of transfer surfaces shall be measured from center points of their opposing...
-
M302.3.2 Leg Supports
Where stirrups are provided, leg supports shall also be provided and comply with M305.4.
-
M302.3 Supports
Transfer supports, leg supports and reclining surfaces shall comply with M302.3.
-
M302.2 Transfer Surface
A transfer surface shall be provided and shall comply with M302.2.
