The turning space shall be a T-shaped space within a 60 inch (1524 mm) square minimum with arms and base 36 inches (914 mm) wide minimum....
Search Results "L-Shaped Seat"
Filters
Commonly Searched Documents
-
11B-304.3.2 T-Shaped space
-
11B-304.3.2 T-Shaped space
The turning space shall be a T-shaped space within a 60 inch (1524 mm) square minimum with arms and base 36 inches (914 mm) wide minimum....
-
L. Availability of Electrical Power
L. Availability of Electrical Power Emergency shelters should have a way to provide a back-up power supply when the electrical service is interrupted....
-
M302.4.2 Clearance Around Base
The base of the diagnostic equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of...
-
5.8.2.1 Height of Breast Platform At Time of Measurement
5.8.2.1 Height of Breast Platform At Time of Measurement. All knee and toe clearances should be measured when the top of the breast platform is set at 34 inches above the floor.
-
Chapter 2: Methodology
[See subsections ...]
-
M302.4.2 Clearance Around Base
The base of the equipment shall provide a clearance 6 inches (150 mm) high minimum measured from the floor and 36 inches (915 mm) deep minimum measured from the edge of the...
-
M302.4 Lift Compatibility (Section-by-Section Analysis)
The MDE NPRM proposed to require that diagnostic equipment used by patients in the seated position be usable with a patient lift and comply with either the proposed clearance in base (proposed...
-
Lift Compatibility (M301.4 and M302.4)
M301.4 and M302.4 would require diagnostic equipment used by patients in a supine, prone, or sidelying position, and diagnostic equipment used by patients in a seated position to be usable...
-
4.34.6 KITCHENS
Accessible or adaptable kitchens and their components shall be on an accessible route and shall comply with the requirements of 4.34.6.
-
11B-221.2.1.6 Specialty seating areas
[ADA Title III] §36.308 Seating in assembly areas. ...
-
Plan 1B: 13-Foot Wide Accessible Guest Room
Features include a standard bathtub with a seat, comparable vanity, clothes closet with swinging doors, and door connecting to adjacent guest room....
-
Access Board: Standard Roll In Shower Stalls
This video is part of a longer animation produced by the U.S. Access Board. View the animation video in its entirety on the Access Board's website...
-
General Seating: ADA Standard Section 221.2.1.1
Section 221.2.1.1 covers scoping requirements in the current ADA Standards for general seating in assembly areas.
-
L. Accessible Guest Rooms
L....
-
Appendix 2- Photos of Participants in the IDEA Center Research
Appendix 2- Photos of Participants in the IDEA Center Research Examples of High Seats: Examples of Very Large and Small Clear Floor Area Widths: Examples of Very Long...
-
Figure 608.5.2 Standard Roll-In Type Shower Compartment Control Location – Drawing from the U.S. Access Board
-
11B-1002.4.7.1 Shoulder-to-shoulder seating
Where an amusement ride provides shoulder-to-shoulder seating, companion seats shall be shoulder-to-shoulder with the adjacent wheelchair space....
-
Pressalit Care Mixer Tap with Long Rotatable Spout and Ring-Shaped Operating Lever
Mixer tap with long rotatable spout and ring-shaped operating lever with water-saving Eco-effect. ...
-
(2) Adjustability: Minimum Low Transfer Height
Additionally, the reports pointed to current accessibility standards for toilet seats, shower seats, and tub seats, which require a height of 17 inches minimum and 19 inches maximum....
-
5. Edge Protection
The MDE NPRM proposed edge protection on the ramps leading up to the raised platform (proposed M303.3.3.4), but did not require edge protection on the raised platforms themselves....
-
M301.2.2, M302.2.2 Transfer Size
M301.2.2, M302.2.2 Transfer Size Proposed requirement: 30" wide minimum and 15" deep minimum • Sub-Committee Recommendation: 28" wide minimum and 17" deep minimum. This...
-
§ 36.406(f) Assembly areas
(f) Assembly areas. Assembly areas subject to the proposed standards shall comply with the provisions applicable to assembly areas, including, but not limited to, sections 221 and...
