The DR series compression seal stands up to any challenge due to an installation process that is not weather sensitive. Features & Benefits: Heavy pedestrian / Heavy...
Search Results "Surface Slope"
Filters
Commonly Searched Documents
-
Inpro Corporation JointMaster® DR Series Seal Expansion Joint Systems
-
NanoPave® JSS 2-in-1 Joint Stabilizer and Sealer
NP-JSS is also a UV resistant, VOC-free sealant that protects and helps maintain the natural beauty of most paving surfaces. ...
-
B5
B5. Are all accessible parking spaces, including the access aisle, relatively level (1:50 or 2%) in all directions? [ADA Standards § 4.6.3] Yes No If No: Look for a...
-
7.4.4 Resting Intervals
Resting intervals shall comply with 7.4.4. Where the trail grade exceeds 1:20 (5 percent), resting intervals shall be provided as specified in Table 7.4.3.1.
-
6.7.1.1
The grade of a Beach Access Route shall be 1:20 (5 percent) or less for any distance.
-
Impact Annenuation [sic]
Surface Impact Testing Results per ASTM F 1292: Phase I surfaces (unaged) and Phase II (exposed for 6 months) Surface/ Test Drop 2 G Drop3G Drop2...
-
Tread Obstacles on Trails
A tread obstacle is anything that interrupts the evenness of the tread surface. On trails, tread obstacles often occur as a result of ruts, roots, and rocks in the tread surface....
-
Department of Justice method
Department of Justice method In the tips and techniques section of "Survey Tools and Techniques," (www.usdoj.gov/crt/ada/ckstools.htm) the checklist states that slopes can be measured...
-
APPENDIX A
of playground surfaces. ...
-
4.1.7(3)(a)
EXCEPTION: A ramp with a slope no greater than 1:6 for a run not to exceed 2 ft (610 mm) may be used as part of an accessible route to an entrance....
-
4.1.7(2)(a)
EXCEPTION: A ramp with a slope no greater than 1:6 for a run not to exceed 2 ft (610 mm) may be used as part of an accessible route at an entrance....
-
Clear Ground Space [1013.2]
The surface of the clear ground space must be firm and stable, but must also accommodate the use of tent stakes or other devices to secure the tent....
-
I. Introduction to the Study
Criteria specify a maximum running slope for a ground level accessible route (1:16 or 6.25%), maximum cross slope (1:48 or 2.08%), minimum clear width (60 inches), limit on a change of level...
-
11B-1008.2.6.1 Accessibility
Ground surfaces shall comply with ASTM F 1951. Ground surfaces shall be inspected and maintained regularly and frequently to ensure continued compliance with ASTM F 1951....
-
Circular Cross Section: ADA Standard Section 505.7.1
Section 505.7.1 covers the current ADA Standards for the circular cross section of handrail gripping surfaces.
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
EZ-ACCESS® Incline Calculator for Ramp Solutions
Refer to your equipment’s (wheelchair or scooter) User Guide for exact recommendations concerning acceptable usage and allowable slope....
-
M301.2.1 Transfer Surface Height
Many X-Ray systems have imaging components such as X-Ray tubes, high voltage generators, and/or detectors located under the table (transfer surface)....
-
Use Zones: ADA Standard Section 1008.2.6.2
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition) (incorporated by reference, see “Referenced Standards” in Chapter 1)....
-
Beneficial Designs The Universal Trail Assessment Process (UTAP)
Suunto clinometer to measure the average grade between two points of the trail; a digital SmartTool inclinometer to measure trail sections for maximum grade and maximum and average cross slope...
-
General: ADA Standard Section 240.1
Section 240.1 of the ADA Standards covers information in the current ADA Standards on scoping requirements for play areas.
-
1008.2.6.1 Accessibility
Ground surfaces shall comply with ASTM F 1951 (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
1008.2.6.1 Accessibility
Ground surfaces shall comply with ASTM F 1951 (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
303.1 General
Where changes in level are permitted in floor or ground surfaces, they shall comply with 303. EXCEPTIONS: 1. Animal containment areas shall not be required to comply with 303. 2....
