Please consult factory for pit type installations. 28.5 inch (72 cm) long ramp and 15 ft (4.5 m) indicator cable included....
Search Results "Exit Ramp"
-
Detecto FHD Series Stationary Wheelchair Scale
-
Changes in Level at Entry to Wheelchair Spaces (M303.3)
Level changes greater than ½ inch high would be required to be ramped....
-
Simplified Building Concepts: ADA - Building an Upright
Video demonstration for building an upright for railings using Simplified Building products.
-
Simplified Building Concepts: Assembling the ADA Railing
Simplified Building Concepts: Assembling the ADA Railing
-
Simplified Building Concepts: ADA - Message to Contractors
Find out how you can use Kee Access ADA components to expand your contracting business
-
Simplified Building Kee Access ADA Railings
Kee Access fittings are used to construct ADA and smooth surface railings
-
5.8.1.2.3 Double Ramped Entry - Edge Protection on the Platform sides Recommendations
5.8.1.2.3 Double Ramped Entry - Edge Protection on the Platform sides Recommendations The Committee recommends a minimum two-inch high edge protection on both sides of the platform for...
-
1003.2.13 Accessible means of egress
Section 1003.2.13 Change to read as shown: (E19-00 & E20-00) 1003.2.13 Accessible means of egress. Accessible means of egress shall comply with Sections 1003.2.13.1 through...
-
5.8.1.2.2 Single Ramped Entry – Edge Protection on the Platform and Platform Sides
5.8.1.2.2 Single Ramped Entry – Edge Protection on the Platform and Platform Sides....
-
1132A.4, Item 3
Changes in height greater than ½ inch (12.7 mm) shall be accomplished by means of a ramp complying with Section 1114A or by means of a platform constructed to the level of the floor as illustrated...
-
4. Access to Newly Constructed and Altered Facilities
In addition, the City will upgrade noncompliant curb ramps and/or install new curb ramps where existing ramps are lacking in connection with street resurfacing and repaving and other major...
-
11B-206.2.19 Pedestrian street crossings
Where walks or sidewalks are provided, a curb ramp, blended transition, or a combination of curb ramps and blended transitions complying with Section 11B-406 shall connect the walks or sidewalks...
-
1132A.5.1 General
The floor or landing on the dwelling unit side of the primary entry door and any required exit door shall have a minimum length of not less than 44 inches (1118 mm)....
-
4.1.2(5)
EXCEPTION: Accessible ramps complying with 4.8 or, if no other alternative is feasible, accessible platform lifts complying with 4.11 may be used in lieu of an elevator....
-
1132A.4, Item 3
Changes in height greater than ½ inch (12.7 mm) shall be accomplished by means of a ramp complying with Section 1114A or by means of a platform constructed to the level of the floor as illustrated...
-
505.4 Height
Top of gripping surfaces of handrails shall be 34 inches (865 mm) minimum and 38 inches (965 mm) maximum vertically above walking surfaces, stair nosings, and ramp surfaces....
-
4.1.6(1)(f)
(f) If an escalator or stair is planned or installed where none existed previously and major structural modifications are necessary for such installation, then a means of accessible...
-
206 Accessible Routes
(ii) Accessible public entrances must be provided in a number at least equivalent to the number of exits required by the applicable building or fire codes....
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
Cross Slope and Surfaces [4.8.6]
Ramp surfaces must comply with requirements for ground and floor surfaces and be "stable, firm, and slip-resistant." A specific level of slip-resistance is not mandated....
