Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
Search Results "Continuous Width"
-
11B-703.5.4 Character proportions
-
502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
8. Term of Settlement Agreement
Term of Settlement Agreement The District Court shall have continuing jurisdiction over this Settlement Agreement throughout the Settlement Agreement’s term....
-
Aisle Stairs and Ramps in Assembly Areas
Section 505.2 states that in assembly areas, a handrail may be provided at either side or within the aisle width when handrails are not provided on both sides of aisle ramps....
-
GOLF CAR PASSAGE
[DSA-AC] A continuous passage on which a motorized golf car can operate....
-
M305.3 Standing Supports
Standing supports shall provide continuous support throughout use of the diagnostic equipment and shall comply with M305.3....
-
§27.125(b)(1)
(1) No order suspending, terminating, or refusing to grant or continue Federal financial assistance becomes effective until:...
-
M305.3 Standing Supports
Standing supports shall provide continuous support throughout use of the diagnostic equipment and shall comply with M305.3....
-
11B-502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
11B-502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings. ...
-
11B-703.5.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
11B-703.2.4 Character proportions
Characters shall be selected from fonts where the width of the uppercase letter “O” is 60 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
-
11B-502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
502.1 General
Where parking spaces are marked with lines, width measurements of parking spaces and access aisles shall be made from the centerline of the markings....
-
Outdoor Recreation Access Route (ORAR)
A continuous, unobstructed path for pedestrian use that connects elements in an outdoor recreation area such as a picnic area, campground, or trailhead....
-
1012.1 General
The technical requirements address the width of parking spaces and pull-up spaces for recreational vehicles (1012.2); the width of parking spaces for vehicles, other than recreational vehicles...
-
1132A.5.2 Strike edge maneuvering space at doors
The width of the level area on the side to which the door swings shall extend 18 inches (457 mm) past the strike edge for all doors....
-
4.8.5* HANDRAILS
The inside handrail on switchback or dogleg ramps shall always be continuous....
-
703.2.7 Character Spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....
-
703.2.7 Character Spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....
-
11B-703.2.7 Character spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....
-
11B-809.8.3 Door maneuvering clearance.
The width of the maneuvering clearance shall extend 18 inches (457 mm) beyond the strike edge at the pull side of the door....
-
11B-703.2.7 Character spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....
-
703.2.7 Character Spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....