[See subsections ...]
Search Results "Bus Ramp"
Commonly Searched Documents
-
§ 37.33 Airport transportation systems
-
11B-218.5 Other transportation facilities
In other transportation facilities, public address systems shall comply with Section 11B-810.7 and clocks shall comply with Section 11B-810.8.
-
§ 38.159(b)(6) Platform surface
(6) Platform surface. The platform surface shall be free of any protrusions of 1/4 inch (6.5 mm) high and shall be slip resistant. The platform shall have a minimum clear width of 28...
-
§ 37.209 Training and other requirements
OTRB operators shall comply with the requirements of §§37.161, 37.165-37.167, and 37.173. For purposes of §37.173, "training to proficiency" is deemed to include, as appropriate...
-
(1)(d)
(d) Faucets and flush controls should be operable with one hand and should not require tight grasping, pinching, or twisting of the wrist. The force required to activate controls...
-
§ 38.159(d)(3) Mobility aids accommodated
(3) Mobility aids accommodated. The securement system shall secure common wheelchairs and mobility aids and shall either be automatic or easily attached by a person familiar with the...
-
11B-218.5 Other transportation facilities
In other transportation facilities, public address systems shall comply with Section 11B-810.7 and clocks shall comply with Section 11B-810.8.
-
f-vi
Is there a level landing, at least 60 inches x 60 inches, when a ramp changes direction? [ADA Standards § 4.8.4] Yes No...
-
5.8.1.2.3 Double Ramped Entry – Edge Protection on the Platform Sides
5.8.1.2.3 Double Ramped Entry – Edge Protection on the Platform Sides....
-
49 CFR Part 37 - Transportation Services for Individuals with Disabilities (ADA) (with amendments issued through 2015)
Authority: 42 U.S.C. 12101-12213; 49 U.S.C. 322. Source: 56 FR 45621, Sept. 6, 1991, unless otherwise noted.
-
Circular Cross Section: ADA Standard Section 505.7.1
Section 505.7.1 covers the current ADA Standards for the circular cross section of handrail gripping surfaces.
-
Gripping Surface: ADA Standard Section 505.6
Section 505.6 covers the current ADA Standards for the handrail gripping surface.
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum.
-
11B-505.6 Gripping surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of handrail gripping surfaces shall not be...
-
R304.5.1.1 Pedestrian Circulation Paths Other Than Shared Use Paths
In pedestrian circulation paths other than shared use paths, the clear width of curb ramp runs, blended transitions, and turning spaces shall be 1.2 m (4.0 ft) minimum....
-
Top Landing [§406.4]
Top Landing [§406.4] The required landing at the top of curb ramps allows an accessible route to connect to the ramp opening....
- citEcar ADA Electric Shuttle 11P 1WC
- citEcar ADA Enclosed Shuttle 11P 1WC
-
Changes in Level at Entry to Wheelchair Spaces (M303.3)
Level changes greater than ½ inch high would be required to be ramped....
-
5.8.1.2.3 Double Ramped Entry - Edge Protection on the Platform sides Recommendations
5.8.1.2.3 Double Ramped Entry - Edge Protection on the Platform sides Recommendations The Committee recommends a minimum two-inch high edge protection on both sides of the platform for...
-
1132A.4, Item 3
Changes in height greater than ½ inch (12.7 mm) shall be accomplished by means of a ramp complying with Section 1114A or by means of a platform constructed to the level of the floor as illustrated...
-
5.8.1.2.2 Single Ramped Entry – Edge Protection on the Platform and Platform Sides
5.8.1.2.2 Single Ramped Entry – Edge Protection on the Platform and Platform Sides....
-
4. Access to Newly Constructed and Altered Facilities
In addition, the City will upgrade noncompliant curb ramps and/or install new curb ramps where existing ramps are lacking in connection with street resurfacing and repaving and other major...