The MDE NPRM proposed a mammography breast platform height range of 30 inches high minimum and 42 inches high maximum above the floor. The Access Board received three comments on...
Search Results "Removable Seat"
-
M303.4.1 Breast Platform Adjustability (Section-by-Section Analysis)
-
5.4.3 Transfer Support Height for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.3 Transfer Support Height for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
608.3.3 Alternate Roll-In Type Shower Compartments
Grab bars shall not be provided above the seat. Grab bars shall be installed 6 inches (150 mm) maximum from adjacent walls....
-
607.2 Clearance
Where a permanent seat is provided at the head end of the bathtub, the clearance shall extend 12 inches (305 mm) minimum beyond the wall at the head end of the bathtub....
-
11B-608.3.3 Alternate roll-in type shower compartments
Grab bars shall not be provided above the seat. Grab bars shall be installed 6 inches (152 mm) maximum from adjacent walls....
-
11B-608.3.3 Alternate roll-in type shower compartments
Grab bars shall not be provided above the seat. Grab bars shall be installed 6 inches (152 mm) maximum from adjacent walls....
-
Clear Floor Space
Clear Floor Space The load and unload areas adjacent to ride seats designed for transfer must have a clear space of 30 by 48 inches minimum....
-
608.3.3 Alternate Roll-In Type Shower Compartments
Grab bars shall not be provided above the seat. Grab bars shall be installed 6 inches (150 mm) maximum from adjacent walls....
-
607.2 Clearance
Where a permanent seat is provided at the head end of the bathtub, the clearance shall extend 12 inches (305 mm) minimum beyond the wall at the head end of the bathtub....
-
607.2 Clearance
Where a permanent seat is provided at the head end of the bathtub, the clearance shall extend 12 inches (305 mm) minimum beyond the wall at the head end of the bathtub....
-
§ 38.125(d)(1) Requirements
All intercity rail cars required to be accessible by §§38.111 (a) and (e) of this subpart shall provide at least one, but not more than two, mobility aid seating location(s) complying with...
-
D. TERMS OF AGREEMENT
The Museum shall remove architectural barriers in existing facilities where such removal is readily achievable, in compliance with 42 U.S.C. § 12182(b)(2)(A)(iv); 28 C.F.R. § 36.304....
-
§ 35.151(e)(2)
(2) Facilities with more than 50 beds covered by this section that provide common use bathing facilities shall provide at least one roll-in shower with a seat that complies with the relevant...
-
Minimum Requirement
.); where fixed seating is provided and where there may be an audio-amplification system....
-
Don-Jo Mfg., Inc. Vertical Rod Protector 83
Number 83 Description Latch Bolt...
-
Architectural Builders Hardware 1811 Vertical Rod Protectors
Assist in accessibility conformance. Use in hospitals and schools, etc. 18 GA. #304 Stainless Steel #4 satin finish. Installs with #6 x 3/4" screws directly into the...
-
Rockwood Manufacturing Vertical Rod Cover BFRC12
The vertical rod cover (BFRC) is a sturdy channel made of .050" stainless steel (other finishes available) designed to fit over the vertical rod, protecting it from damage caused by...
-
Don-Jo Mfg., Inc. Vertical Rod Protector 85
Product Specifications Number 85 Description Rod...
-
Don-Jo Mfg., Inc. Vertical Rod Protector 81
Product Specifications Number 81 Description Latch Bolt...
-
ElectionSource Voter Accessibility Expansion Door Hinge
Add 2'' of width to any doorway in your offices! Excellent for use on bathroom doors which are usually a tight fit for those in wheelchairs. Easy to install, uses same screws and...
-
Stanley FBB 269 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
Steel – polished and plated or phosphated and prime coated for painting or Stainless Steel – highly polished or satin finish. For corridor doors to patients’ rooms, operating...
-
Rockwood Manufacturing Company BFRC24 Vertical Rod Cover
The vertical rod cover (BFRC) is a sturdy channel made of .050" stainless steel (other finishes available) designed to fit over the vertical rod, protecting it from damage caused by...
-
McGuire Manufacturing Co., Inc. Retrofit Insulation Kit for P-Trap
1 1/4 x 1 1/2" seamless retrofit P-Trap kit. Furnished with seamless J-Bend cover, wall bend cover, drain tailpiece, riser tube, angle stop, and wheel handle covers.
