Handrail gripping surfaces shall have a cross section complying with Section 11B-505.7.1 or 11B-505.7.2.
Search Results "Parallel Curb Ramp"
Filters
Commonly Searched Documents
-
11B-505.7 Cross section
-
Parking Spaces: ADA Standard Section 208
Section 208 covers scoping requirements in the most current ADA Standards for parking spaces.
-
11B-208 Parking spaces
[See subsections ...]
-
Slope Meters and Levels
Corada has reviewed several models of slope meters and levels to assist accessibility surveyors in measuring slope and level changes. The following are the models that can be...
-
1015.3 Height
On ramps and ramped aisles, from the ramp surface at the guard....
-
1132A.4, Item 4
., concrete, brick, flagstone) may have a maximum change in height from the interior landing of 1 inch (25.4 mm), provided a ramp with a maximum slope of 1:8 is permanently installed....
-
406.3 Sides of Curb Ramps
Where provided, curb ramp flares shall not be steeper than 1:10. Figure 406.3 Sides of Curb Ramps...
-
SafePath: Overview of Ramps and Reducers for ADA Compliance by SafePath Products
SafePath™ manufactures ramps, landings, seismic surface transitions, flooring reducers and other industrial and residential products for ADA (American's with Disability Act) and access code...
-
1015.3 Height
On ramps and ramped aisles, from the ramp surface at the guard....
-
3. Exception to Ramp Running Slope
A ramp in the built environment to which this exception applies may use a 1:2 grade slope on a short rise ramp....
-
§ 38.125(c)(1) Design load
Ramps or bridge plates 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp or bridge plate distributed over an area of 26 inches by 26 inches, with...
-
Americans with Disabilities Act (ADA) Standards for Transportation Facilities
based on the Board's ADA Accessibility Guidelines (ADAAG) but include additional requirements concerning: Location of Accessible Routes (206.3) Detectable Warnings on Curb...
-
§ 38.159(c)(1) Design load
Ramps 30 inches (760 mm) or longer shall support a load of 600 pounds (2665 N), placed at the centroid of the ramp distributed over an area of 26 inches by 26 inches (660 mm by 660 mm),...
-
Portable ramp - greater than six inch step
[See subsections ...]
-
11B-809.9.1 Clear floor space
762 mm) by 48 inches (1219 mm), with centerlines aligned with the centerline of the work surface, appliance, sink or fixture, shall be provided in the following locations: For a parallel...
-
4.31.3* Mounting Height
The highest operable part of the telephone shall be within the reach ranges specified in 4.2.5 or 4.2.6.
-
4.5.2.2 Side Approach
The clear floor or ground space for a side approach shall be 30 inches (760 mm) by 60 inches (1525 mm).
-
§ 38.125(c)(7) Stowage
A compartment, securement system, or other appropriate method shall be provided to ensure that stowed ramps or bridge plates, including portable ramps or bridge plates stowed in the passenger...
-
4.7.9.2 Clear Floor or Ground Space
Clear floor or ground space 48 inches (1220 mm) by 30 inches (760 mm) oriented for a forward or parallel approach shall be provided for utility sinks required to meet 4.7.9....
-
T202 Accessible Means of Boarding and Alighting
These vehicles must also provide access to the roadway in the event passengers must be offloaded where there is no platform or curb....
-
R407.6.1 Slope
R407.6.1 Slope. Landing slopes shall be 2 percent maximum in any direction.
-
1013.3 Height
On ramps, from the ramp surface at the guard. Exceptions: 1. ...
-
Requirements to Remember for ADA Compliance in Construction Projects: Transportation Facilities
Access Board’s updated ADA (and ADAAG) guidelines but includes a few additional requirements concerning: Location of Accessible Routes (206.3) Detectable Warnings on Curb...
-
11B-810.2.3 Connection
constructed bus stop boarding and alighting areas shall provide a detectable transition between the boarding/alighting area and the roadway; the detectable transition shall consist of a curb...
