Where reinforcement is installed at the back, it shall be installed between 30 inches (762 mm) maximum and 38 inches (965 mm) minimum above the finish floor....
Search Results "Maximum Dimension"
-
11B-809.10.7.3 Reinforcement for grab bars
-
11B-1003.3.1 Boat slip clearance
Each 10 feet (3048 mm) maximum of linear pier edge serving boat slips shall contain at least one continuous clear opening 60 inches (1524 mm) wide minimum....
-
Boat Slip Clearance: ADA Standard Section 1003.3.1
Each 10 feet (3050 mm) maximum of linear pier edge serving boat slips shall contain at least one continuous clear opening 60 inches (1525 mm) wide minimum. EXCEPTIONS: 1....
-
11B-1003.3.1 Boat slip clearance
Each 10 feet (3048 mm) maximum of linear pier edge serving boat slips shall contain at least one continuous clear opening 60 inches (1524 mm) wide minimum....
-
BitStarz 30 Free Spins: Player Review of Bonuses, Games & Cashout Options
Players should also look for restrictions involving maximum bets, qualifying games, contribution percentages, and maximum eligible winnings....
-
Surfaces (R302.7) (Section-by-Section Analysis)
Elongated openings in gratings must be placed so that the long dimension is perpendicular to the dominant direction of travel....
-
M301.4.2 Clearance Around Base (Section-by-Section Analysis)
The width of the base permitted within this clearance would be 26 inches maximum at the edge of the examination surface and was permitted to increase at a rate of 1 inch in width for every...
-
Midmark 630 HUMANFORM™ Procedures Table
seat height and 650-pound weight capacity Power height, back, foot and tilt Hand and foot controls standard Patient Weight Capacity: 650 lb (295 kg) Height: Minimum 18" (45.7 cm), Maximum...
-
11B-703.5.8 Character spacing
Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height....
-
Character Spacing: ADA Standard Section 703.5.8
Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height....
-
11B-703.5.8 Character spacing
Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height....
-
Coat Hooks and Shelves: ADA Standard Section 604.8.3
Section 604.8.3 covers the current ADA Standards for coat hooks and shelves in an ambulatory accessible compartment.
-
11B-406.3.2 Turning space
The slope of the turning space in all directions shall be 1:48 maximum....
-
11B-406.3.2 Turning space
The slope of the turning space in all directions shall be 1:48 maximum....
-
Unobstructed: ADA Standard Section 308.2.1
Section 308.2.1 covers the current ADA Standards for unobstructed forward reach.
-
Coat Hooks and Shelves: ADA Standard Section 603.4
Section 603.4 covers the current ADA Standards for coat hooks and shelves in toilet and bathing rooms.
-
11B-308.2.1 Unobstructed
Where a forward reach is unobstructed, the high forward reach shall be 48 inches (1219 mm) maximum and the low forward reach shall be 15 inches (381 mm) minimum above the finish floor or...
-
11B-308.2.1 Unobstructed
Where a forward reach is unobstructed, the high forward reach shall be 48 inches (1219 mm) maximum and the low forward reach shall be 15 inches (381 mm) minimum above the finish floor or...
-
Pilot Rock APTX Full Sized Pedestal Rectangular Utility Tables
These utility tables can be 6 or 8 ft. long and offer 30" table height (nominal dimensions). ...
-
Seat Height: ADA Standard Section 1009.2.4
The height of the lift seat shall be designed to allow a stop at 16 inches (405 mm) minimum to 19 inches (485 mm) maximum measured from the deck to the top of the seat surface when in the...
-
Measuring Techniques
Software later allows the calculation of point-to-point distances and other dimensions....
-
Urinal Depth
In the proposed rule, the Board sought to clarify the requirement in the original ADAAG that accessible urinals have an "elongated" rim by specifying a minimum dimension of 13 ½ inches,...
-
4.10.3 Hall Call Buttons
Call buttons shall be a minimum of 3/4 in (19 mm) in the smallest dimension. The button designating the up direction shall be on top. (See Fig. 20.) Buttons shall be raised or flush....
-
4.10.3 HALL CALL BUTTONS
Call buttons shall be a minimum of 3/4 in (19 mm) in the smallest dimension. The button designating the up direction shall be on top (see Fig. 20). Buttons shall be raised or flush....
