Characters shall be selected from fonts where the width of the uppercase letter “O” is 55 percent minimum and 110 percent maximum of the height of the uppercase letter “I”....
Search Results "Maximum Dimension"
-
Character Proportions: ADA Standard Section 703.5.4
-
1009.6.1 Travel distance
The maximum travel distance from any accessible space to an area of refuge shall not exceed the exit access travel distance permitted for the occupancy in accordance with Section 1017.1....
-
Height: ADA Standard Section 902.3
The tops of dining surfaces and work surfaces shall be 28 inches (710 mm) minimum and 34 inches (865 mm) maximum above the finish floor or ground....
-
Transfer Height: ADA Standard Section 1002.6.2
The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
11B-809.10.7.4 Seat height
Water closet seats shall be 15 inches (381 mm) minimum and 19 inches (483 mm) maximum measured to the top of the seat above the finish floor....
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
11B-902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (711 mm) minimum and 34 inches (864 mm) maximum above the finish floor or ground....
-
11B-902.3 Height
The tops of dining surfaces and work surfaces shall be 28 inches (711 mm) minimum and 34 inches (864 mm) maximum above the finish floor or ground....
-
11B-809.10.7.4 Seat height
Water closet seats shall be 15 inches (381 mm) minimum and 19 inches (483 mm) maximum measured to the top of the seat above the finish floor....
-
Caroma® USA Sydney Low Profile 270 Easy Height Round Front Plus Toilet
The dimensions in this sheet may change with amendments to the standards....
-
C101.4 Units of Measurement (Section-by-Section Analysis)
This proposed section is new to the 255 Guidelines, and would clarify dimensions stated in the text of the guidelines or referenced standards....
-
1016.6 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
R304.2.1 Turning Space
The 1.5 m (5.0 ft) dimension shall be provided in the direction of the ramp run....
-
5.2.2.1 Transfer Surface Width Recommendations for M302
Rationale for final recommendation The Committee considered the dimensions for rectangular seats in roll-in showers from the 2010 Standards; and the ideal chair width recommended in Architectural...
-
R304.3.1 Turning Space
The 1.5 m (5.0 ft) dimension shall be provided in the direction of the pedestrian street crossing....
-
4.30.4* Raised and Brailled Characters and Pictorial Symbol Signs
The border dimension of the pictogram shall be 6 in (152 mm) minimum in height....
-
1016.6 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
Knee Clearance: Clearance as Measured from Distal Knee Point - Manual Wheelchair
It references dimensions of clearance height and depth to the distal knee point on a person....
-
Knee Clearance: Clearance as Measured from Anterior-Most Abdomen Point - Manual Wheelchair
It references dimensions of clearance height and depth to the forward-most abdomen point on a person....
-
11B-703.6.1 Pictogram field
The 6-inch vertical dimension applies to the field, not the symbol. The symbol may be smaller than the field....
-
11B-604.7 Dispensers and disposal units
Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser...
-
11B-604.7 Dispensers and disposal units
Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser...
-
11B-411.2.1.2.3 Accessibility function button
Each dot shall have a base diameter of 0.059 inch (1.5 mm) minimum and 0.063 inch (1.6 mm) maximum and a height of 0.025 inch (0.6 mm) minimum and 0.037 inch (0.9 mm) maximum....
