Outside diameter 6 15/16" (175mm), inside diameter 5 1/2" (140mm), chute depth 5" (130mm). Rough Countertop Cutout: 5 5/8" diameter (140mm)....
Search Results "Counter Depth"
Filters
Commonly Searched Documents
-
Bobrick Countertop-Mounted Circular Waste Chute B-529
-
What is a good un-official "working" definition of "work surface"?
11B-805.7 goes on to list numerous items that would/could be included in the broad verbiage of "Built-in cabinets, counters and work surfaces"....
-
Assisted Living Directory
to be the model of honesty and transparency in the assisted living and senior care industry by providing accurate and highly trustworthy facility information, caregiver support, and in-depth...
-
Neo-Metro Commercial Wall Mounted Neo-Basin 8935 Series
Model 8935 features 2.5" extended counter on both sides while Model 8936 does not. A trap enclosure is standard on both versions....
-
Oval Window Audio Portable InfoLoop Hearing System
microphone Automatic gain control Noise gating electronics Loop wire antenna 5-8 hour rechargeable battery The Portable InfoLoop is ideal for meetings (left) information/sales counters...
-
ASI Global Partitions Plastic Laminate Partitions
Plastic laminate is available in all four installation styles and a variety of designer colors to complement vanities and counter tops....
-
2. Equipment Clearances for Breast Platforms
The proposed rule included a requirement that 17 inches minimum and 25 inches maximum of the 48-inch wheelchair space depth include knee and toe clearance....
-
Table Surface Height
These commenters recommended that where only a portion of counters are made accessible, the accessible height should be 31 inches maximum....
-
A4.1.1(3) Areas Used Only by Employees as Work Areas
., laboratories, service counters, ticket booths), 5%, but not less than one, of each type of work station should be constructed so that an individual with disabilities can maneuver within...
-
Employee Work Areas [§206.2.8]
This applies to the size of work areas as defined by permanently installed walls, partitions, counters, casework, or furnishings, but not modular partitions or furnishings, including systems...
-
Bobrick TrimLineSeries Recessed Sanitary Napkins Disposal B-35303
Rough Wall Opening: 11 1⁄2" W, 17 1⁄4" H, 3 3⁄4" min. depth (290 x 440 x 95mm)....
-
Priority 3: Toilet Rooms
Word Fillable Form (2.4MB) Word Non-Fillable Form (2.2MB) PDF Non-Fillable Form (0.7MB)
-
11B-205.1 General
Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309....
-
Soiltac Liquid Topical
The stabilizer has a penetration depth of 1/8 inch. The first noticeable signs of change for this surface came after the first heavy rainfall at the March 2008 testing....
-
809.2.2 Turning Space
EXCEPTION: Turning space shall not be required in exterior spaces 30 inches (760 mm) maximum in depth or width. Advisory 809.2.2 Turning Space....
-
11B-705.2 Detectable directional texture
The depth of the texture shall not be less than 36 inches (914 mm). FIGURE 11B-705.2 ‡‡ DETECTABLE DIRECTIONAL TEXTURE...
-
M303.2.2 Width (Section-by-Section Analysis)
(Significant Changes – Width and Depth of Wheelchair Spaces), and discussed briefly below....
-
Section 5 References
“Revised Knee Clearance Depth and Footrest Clearance dimensions for sizing of mammography equipment.” Memorandum. April 23, 2013....
-
809.2.2 Turning Space
EXCEPTION: Turning space shall not be required in exterior spaces 30 inches (760 mm) maximum in depth or width. Advisory 809.2.2 Turning Space....
-
Teeing Grounds
A rectangular area usually two club-lengths in depth, the teeing ground’s borders are defined by the outside limits of two “tee-markers.”...
-
5.3.2 Transfer Sides Recommendations for M301
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface....
-
5.7.1 Lift Compatibility Clearance in Base for M301
Where the width of the examination surface is less than 36 inches, the clearance depth shall extend the full width of the equipment....
-
809.2.2 Turning Space
EXCEPTION: Turning space shall not be required in exterior spaces 30 inches (760 mm) maximum in depth or width. Advisory 809.2.2 Turning Space....
