Rough Wall Opening: 11 1/4" W, 9 1/2" H, 4" min. depth (285 x 240 x 100mm)....
Search Results "Sink Depth"
Filters
Commonly Searched Documents
-
Bobrick ConturaSeries Recessed Sanitary Napkin Disposal B-4353
-
Bobrick Countertop-Mounted Circular Waste Chute B-529
Outside diameter 6 15/16" (175mm), inside diameter 5 1/2" (140mm), chute depth 5" (130mm). Rough Countertop Cutout: 5 5/8" diameter (140mm)....
-
Playground Study Site
The remaining area of approximately 190 m2 (2,020 ft2 ) was converted to a full-depth EWF surface (Fig. 1)....
-
Re: Service Counters
The entire depth of the lowered counter at 34" max height must be provided to allow for this unimpeded interaction instead of the higher employee counter condition which prevents equal access...
-
11B-205.1 General
Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309....
-
11B-205.1 General
Where two or more outlets are provided in a kitchen above a length of counter top that is uninterrupted by a sink or appliance, one outlet shall not be required to comply with 309....
-
Bobrick TrimLineSeries Recessed Sanitary Napkins Disposal B-35303
Rough Wall Opening: 11 1⁄2" W, 17 1⁄4" H, 3 3⁄4" min. depth (290 x 440 x 95mm)....
-
Tork Toilet Seat Cover Dispenser
Product Data System - V1 - toilet seat cover system Material - Plastic Height - 12.4 in Width - 16.7 in Depth - 2.3 in Color - Black...
-
Bobrick TrimLineSeries Recessed Paper Towel Dispenser B-35903
Rough Wall Opening: 11 1⁄4" W, 15 5⁄8" H, 4" min. depth (285 x 395 x 100mm)....
-
Bobrick Recessed Paper Towel Dispenser/Waste Receptacle B-39003
Rough Wall Opening: 16" W, 54 3⁄4" H, 7 7⁄8" min. depth (405 x 1390 x 200mm)....
-
Bobrick ClassicSeries Recessed Sanitary Napkins Disposal B-353
Rough Wall Opening: 11 1/4" W, 15 5/8" H, 4" min. depth (285 x 395 x 100mm)....
-
Re: Service Counters
For code compliance, one must create a reasonable standard for sufficient depth for accessible use. Reasonable persons will disagree on that number. Why bother? ...
-
M305.2.2 Length (Section-by-Section Analysis)
there was no requirement for length of the transfer support; however, the MDE NPRM preamble noted that the Access Board was considering requiring the transfer supports to extend the entire depth...
-
M301.3.1 Transfer Supports
A) For transfer depths less than or equal to 24 inches a transfer support will be located opposite the transfer side....
-
Moisture and Durability
The trendline fitted to the data of the moisture profile in E2 indicates that it is saturated at a depth of approximately 100 mm (4”) and continues to be saturated to the drainage bed....
-
How to Measure Transfer Surface Height
The lower wheelchair illustrates a typical diagonal transfer.24 Figure 11: Corner radii of a medical examination table The depth and width are measured along the centerlines of...
-
Test Procedures
The EWF surface was excavated throughout its entire 0.3-m (12-in.) depth to determine the moisture profile of the surfacing system....
-
Recommended Objective Test Method and Performance Specifications
Firmness Penetration Depth Firmness Rating Firm 0.3 inch or less 3 or lower Moderately Firm >0.3 to 0.5 inch >3 to 5 Not...
-
2.6
with lines of sight comparable to those for members of the general public, (b) including wheelchair spaces as an integral part of the fixed seating plan, (c) providing the appropriate depth...
-
Alterations: Alternate Stalls
Alternate designs in ADAAG Figure 30(b) allow narrower stall widths while requiring greater depth....
-
1134A.7, Item 1
may be reduced to 36 inches (914 mm) for lavatories, cabinets, wing walls, or privacy walls located immediately adjacent to a water closet which extend no more than 24 inches (610 mm) in depth...
-
Just Manufacturing Enviro Series ADA 30° Wall Hung Lavatory System Package
Undermount of sink to have smooth sound deadening to insulate for sound and reduce condensation. Tapered front bowl wall provides greater ADA Compliant access....
