Risers shall be sloped or the underside of the nosing shall have an angle not less than 60 degrees from the horizontal....
Search Results "Horizontal Standing Support"
-
4.9.3 Nosings
-
4.9.3 NOSINGS
Risers shall be sloped or the underside of the nosing shall have an angle not less than 60 degrees from the horizontal....
-
§ 38.107(a)(3)
(3) A grab bar at least 24 inches long shall be mounted behind the water closet, and a horizontal grab bar at least 40 inches long shall be mounted on at least one side wall, with one end...
-
§ 38.123(a)(3)
(3) A grab bar at least 24 inches long shall be mounted behind the water closet, and a horizontal grab bar at least 40 inches long shall be mounted on at least one side wall, with one end...
-
§ 38.23(b)(10) Platform movement
The maximum platform horizontal and vertical acceleration when occupied shall be 0.3g....
-
§ 38.125(b)(10) Platform movement
The maximum platform horizontal and vertical acceleration when occupied shall be 0.3g....
-
§ 38.83(b)(10) Platform movement
The maximum platform horizontal and vertical acceleration when occupied shall be 0.3g....
-
§ 38.95(b)(10) Platform movement
The maximum platform horizontal and vertical acceleration when occupied shall be 0.3g....
-
§382.57(a)(1)
., each cluster of kiosks and all stand-alone kiosks at the airport) meets this specification....
-
§ 382.57(a)(1)
., each cluster of kiosks and all stand-alone kiosks at the airport) meets this specification....
-
Don-Jo Mfg., Inc. 2-3/4" Hospital Latch 4500
Shelf pack 1 Features UL Listed, Works with 1-3/4" doors, Lever projection 3-1/4", Non Handed, Push/Pull latch can be mounted with the handles up, down or horizontal...
-
504.3 Prompts
operation that prompts authors to create content that conforms to Level A and Level AA Success Criteria and Conformance Requirements in WCAG 2.0 (incorporated by reference, see 702.10.1) for supported...
-
GRAB BAR
[DSA-AC & HCD 1-AC] A bar for the purpose of being grasped by the hand for support. Advisory Definition of GRAB BAR....
-
GRAB BAR
[DSA-AC & HCD 1-AC] A bar for the purpose of being grasped by the hand for support. Advisory Definition of GRAB BAR....
-
Smith System Flex Single-Student Desk 01368 & 01371
Its design moves the support away from the corners so the student has more knee room for easier ingress/egress, saving time she/he stands up or sits down....
-
GameTime Sounds of Water Panel
Add to a PlayTrails play pocket or use along any trail or pathway as a stand-alone educational sign to maximize the value in your play space....
-
Nana Wall Systems, Inc. Sliding Glass Walls With Solid Wood HSW66
The system is a completely top-supported design therefore the number of panels is only limited by the supporting structure in your design. ...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
1131A.1 Changes in level not exceeding ½ inch
When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
R308.1.2.1 Platform and Vehicle Floor Coordination
Department of Transportation regulations (49 CFR parts 37 and 38) require the height of the vehicle floor and the station platform to be coordinated so as to minimize the vertical and horizontal...
-
7(2)(b)(v)
(v) Vanities and lavatories are installed with the centerline of the fixture a minimum of 1'3" horizontally from an adjoining wall or fixture....
-
Cross Slope
This may be expressed as the percentage of change in elevation or as a ratio of vertical distance to horizontal distance....
-
§ 38.93(d)(3) Exception
Where platform set-backs do not allow the horizontal gap or vertical alignment specified in paragraph (d)(1) or (d)(2) of this section, car, platform or portable lifts complying with §38.95...
-
§ 38.95(b)(7) Platform gaps
When the lift is at car floor height with the inner barrier down (if applicable) or retracted, gaps between the forward lift platform edge and car floor shall not exceed 1/2 inch horizontally...
