and techniques section of "Survey Tools and Techniques," (www.usdoj.gov/crt/ada/ckstools.htm) the checklist states that slopes can be measured in three ways: with a land survey to shoot grades...
Search Results "Finished Grade"
-
Department of Justice method
-
11B-106.5 Defined terms
WORK AREA ENFORCING AGENCY ENTRANCE EQUIVALENT FACILITATION EXISTING BUILDING OR FACILITY EXIT FACILITY FUNCTIONAL AREA GANGWAY GOLF CAR PASSAGE GRAB BAR GRADE...
-
Newly Constructed Tabled Intersections That Contain Pedestrian Street Crossings With Yield or Stop Control (Section-by-Section Analysis)
The cross slope of the pedestrian access route within the pedestrian street crossing is the longitudinal grade of the street being crossed, and the 2 percent maximum cross slope requirement...
-
R208.1 Where Required
Pedestrian at-grade rail crossings not located within a street or highway; 4....
-
11B-605.4 Flush controls
Hand operated flush controls shall comply with Section 11B-309 except that the flush control shall be mounted at a maximum height of 44 inches (1118 mm) above the finish floor....
-
What is the minimum level of slip resistance required by the standards?
Standard methods to prevent or minimize slipperiness in the specification of floor materials, textures, applications, and finishes may be sufficient for compliance with the standards. ...
-
Salsbury Industries 66016 Standard Metal Locker with Box Style Bridge
Requires the Registered User plan or above. Login! -
EXHIBIT A Required Accessible Elements at QuikTrip Stores
grade....
-
General [4.5.1]
Many variables affect the performance of a given walking surface, including slope and cross slope, its material, jointing, texture, and finish, the presence of moisture or contaminants,...
-
DORMA 8600 Series Door Closer
Grade 1 Surface Applied Door Closers The 8600 door closer series is a non-handed surface applied door closer with adjustable spring power and backcheck positioning adjustment....
-
5. Reassignment to a Vacant Position
An employer may reassign an individual to a lower graded position if there are no accommodations that would enable the employee to remain in the current position and there are no positions...
-
29. Admission and recruitment
Under the proposed regulation, overall success in an education program, not just first-year grades, was the criterion against which admissions tests were to be validated....
-
Test Courses & Surfaces
This “access route” was 574.2 ft (175.0 m) in length, and included two 137 ft (41.8 m) sections with grades of 4% to 5% (one uphill, one downhill), and two 30-foot (9.1 m) ramps with grades...
-
11B-810.4 Bus signs
Bus route identification signs shall comply with Sections 11B-703.5.1 _|Finish and Contrast|_ through 11B-703.5.4 _|Character Proportions|_, and Sections 11B-703.5.7 _|Stroke Thickness|_...
-
1134A.8, Item 1
The top of the fixture rim shall be a maximum of 34 inches (864 mm) above the finished floor....
-
Spa
Slip resistant oil finish on wood floors in the spa and bathroom Spa pre-heated with solar panels Thermal mass in the greenhouses to store heat during the day and release...
-
1134A.8, Item 1
The top of the fixture rim shall be a maximum of 34 inches (864 mm) above the finished floor....
-
11B-407.2.2.2 Visible signals
Visible signal fixtures shall be centered at 72 inches (1829 mm) minimum above the finish floor or ground....
-
11B-810.4 Bus signs
Bus route identification signs shall comply with Sections 11B-703.5.1 _|Finish and Contrast|_ through 11B-703.5.4 _|Character Proportions|_, and Sections 11B-703.5.7 _|Stroke Thickness|_...
-
11B-407.2.2.2 Visible signals
Visible signal fixtures shall be centered at 72 inches (1829 mm) minimum above the finish floor or ground....
-
404.2.7 Door and Gate Hardware
Operable parts of such hardware shall be 34 inches (865 mm) minimum and 48 inches (1220 mm) maximum above the finish floor or ground....
-
404.2.7 Door and Gate Hardware
Operable parts of such hardware shall be 34 inches (865 mm) minimum and 48 inches (1220 mm) maximum above the finish floor or ground....
-
404.2.7 Door and Gate Hardware
Operable parts of such hardware shall be 34 inches (865 mm) minimum and 48 inches (1220 mm) maximum above the finish floor or ground....
