The depth of the texture shall not be less than 36 inches (914 mm)....
Search Results "Sink Depth"
Filters
Commonly Searched Documents
-
11B-705.2 Detectable directional texture
-
11B-705.1.2.2.2.2 Two entrance/exit points
Where it is technically infeasible to provide a minimum 108 inches (2743 mm) wide turning space, as measured perpendicular to the curb, the depth of detectable warnings may be reduced to...
-
11B-407.4.1 Car dimensions
prohibits strict compliance with Section 11B-407.4.1, existing elevator car configurations that provide a clear floor area of 18 square feet (1.67 m2) minimum and also provide an inside clear depth...
-
M301.4 Lift Compatibility
Where the width of the examination surface is less than 36 inches (915 mm), the clearance depth shall extend the full width of the equipment....
-
Soiltac Powder Mix-In
The stabilizer has a penetration depth of 4 inches....
-
Wikk Industries Inc. Push Plate 4 1/2 Inch ROUND SWITCHES
304 Stainless Steel in Brushed Satin Finish US32D (630) Dependable & Responsive Easy to Install Single Pole Double Throw (S.P.D.T.) momentary switch requires 3/4" (19mm) mounting depth...
-
Wikk Industries Inc. Push Plate 6 Inch ROUND SWITCHES
Responsive Easy to Install Cover Plate is Type 304 Stainless Steel in Brushed Satin Finish US32D(630) Single Pole Double Throw (S.P.D.T.) momentary switch requires 3/4" (19mm) mounting depth...
-
11B-213.3.4 Lavatories
Where lavatories are provided, at least five percent but no fewer than one shall comply with Section 11B-606 _|Lavatories and Sinks|_ and shall not be located in a toilet compartment....
-
Dimensions for Adults and Children [§102]
These provisions address access for children to: drinking fountains (§602) water closets and toilet compartments (§604) lavatories and sinks (§606) and dining...
-
APPENDIX A. GUIDELINES FOR SERVICE ANIMAL RELIEF AREAS (SARA)
SARAs should include a sink with a faucet for hand washing....
-
Tork Toilet Seat Cover Dispenser, 1/2 Fold
Product Data System - V1 - toilet seat cover system Material - Plastic Height - 11.5 in Width - 16 in Depth - 3 in Color - White...
-
Re: Service Counters
For code compliance, one must create a reasonable standard for sufficient depth for accessible use. Reasonable persons will disagree on that number. Why bother? ...
-
Tork Toilet Seat Cover Dispenser White
Product Data System - V1 - toilet seat cover system Material - Plastic Height - 12.4 in Width - 16.7 in Depth - 2.3 in Color - White...
-
Bobrick ConturaSeries Recessed Sanitary Napkin Disposal B-4353
Rough Wall Opening: 11 1/4" W, 9 1/2" H, 4" min. depth (285 x 240 x 100mm)....
-
Bobrick Countertop-Mounted Circular Waste Chute B-529
Outside diameter 6 15/16" (175mm), inside diameter 5 1/2" (140mm), chute depth 5" (130mm). Rough Countertop Cutout: 5 5/8" diameter (140mm)....
-
Priority 3: Toilet Rooms
Word Fillable Form (2.4MB) Word Non-Fillable Form (2.2MB) PDF Non-Fillable Form (0.7MB)
-
2. Equipment Clearances for Breast Platforms
The proposed rule included a requirement that 17 inches minimum and 25 inches maximum of the 48-inch wheelchair space depth include knee and toe clearance....
-
Bobrick TrimLineSeries Recessed Sanitary Napkins Disposal B-35303
Rough Wall Opening: 11 1⁄2" W, 17 1⁄4" H, 3 3⁄4" min. depth (290 x 440 x 95mm)....
-
11B-705.2 Detectable directional texture
The depth of the texture shall not be less than 36 inches (914 mm). FIGURE 11B-705.2 ‡‡ DETECTABLE DIRECTIONAL TEXTURE...
-
M303.2.2 Width (Section-by-Section Analysis)
(Significant Changes – Width and Depth of Wheelchair Spaces), and discussed briefly below....
-
Section 5 References
“Revised Knee Clearance Depth and Footrest Clearance dimensions for sizing of mammography equipment.” Memorandum. April 23, 2013....
-
Teeing Grounds
A rectangular area usually two club-lengths in depth, the teeing ground’s borders are defined by the outside limits of two “tee-markers.”...
-
5.3.2 Transfer Sides Recommendations for M301
The transfer surface shall be located to provide options to transfer from a mobility device onto one short side (depth) and one long side (width) of the surface....
-
5.7.1 Lift Compatibility Clearance in Base for M301
Where the width of the examination surface is less than 36 inches, the clearance depth shall extend the full width of the equipment....
