Dispenses single- or half-fold paper toilet seat covers from beveled opening. Dispenser fills from bottom through concealed opening. Capacity: 250 toilet seat covers....
Search Results "Patient Seated in Wheelchair"
-
Gamco Surface Mounted Seat-Cover Dispenser - TSC-1
-
M301.1 General
Where diagnostic equipment is used by patients in a supine, prone, or side-lying position, it shall comply with M301....
-
Battery-powered Wheelchairs
Battery-powered Wheelchairs Carriers must accept a passenger’s battery-powered wheelchair, including the battery, as checked baggage unless baggage compartment size and aircraft airworthiness...
-
382.129 What other requirements apply when passengers’ wheelchairs, other mobility aids, and other assistive devices must be disassembled for stowage?
382.129 What other requirements apply when passengers’ wheelchairs, other mobility aids, and other assistive devices must be disassembled for stowage?...
-
5.2.1.4 Transfer Surface Size Recommendations for Imaging Equipment (M301)
The transfer surface must be located so the 28-inch long dimension is parallel to the patient scanning/imaging side of the table....
-
Preferred Seat Widths
The seat width percentiles remained the same for transfers to and from the station and within each protocol....
-
Section 35.151(g) Assembly Areas (Section-by-Section Analysis)
The Department has become aware that a growing trend in the design of large sports facilities is to provide wheelchair seating on removable platforms that seat four or more wheelchair users...
-
1607A.8.2 Grab bars, shower seats and dressing room bench seats
1607A.8.2 Grab bars, shower seats and dressing room bench seats....
-
Acess-Able Designs Portable Tub/Shower Transfer Bench SH-425
First commercial-grade portable tub/shower seat on the market. ...
-
4.16.3* Height
The height of water closets shall be 17 in to 19 in (430 mm to 485 mm), measured to the top of the toilet seat (see Fig. 29(b))....
-
4.16.3* HEIGHT
The height of water closets shall be 17 in to 19 in (430 mm to 485 mm), measured to the top of the toilet seat (see Fig. 29(b))....
-
4.26.3(2)
(2) Shear stress induced in a grab bar or seat by the application of 250 lbf (1112N) shall be less than the allowable shear stress for the material of the grab bar or seat....
-
M305.2.2.1 End Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.1 and M305.2.2.1 shall be 15 inches (380 mm) long minimum. Transfer supports shall be positioned along 13 ½ inches...
-
M305.2.4.1 Circular Cross Section
Transfer supports with circular cross sections shall have an outside diameter of 1 ¼ inches (32 mm) minimum and 2 inches (51 mm) maximum.
-
M305.2.1.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be capable of supporting transfer on each side of the transfer surface.
-
M305.2.1.1 End Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.1 and M302.2 shall be located on the short side (length) opposite the transfer side.
-
M305.2.2.2 Side Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.2 shall be 28 inches (710 mm) long minimum and shall be positioned along the width of transfer...
-
Amos Winter: The cheap all-terrain wheelchair | TED Talks
How do you build a wheelchair ready to blaze through mud and sand, all for under $200?...
-
1607A.8.2 Grab bars, shower seats and dressing room bench seats
Grab bars, shower seats and dressing room bench seat systems shall be designed to resist a single concentrated load of 250 pounds (1.11 kN) applied in any direction at any point on the grab...
-
1607A.8.2 Grab bars, shower seats and dressing room bench seats
Grab bars, shower seats and dressing room bench seat systems shall be designed to resist a single concentrated load of 250 pounds (1.11 kN) applied in any direction at any point on the grab...
-
Access-Able Designs Tub Transfer Bench SH-414-2SDL
Use this seat with the fold-down legs when there is no inner ledge for the regular seat to rest on. ...
-
4.26.3(1)
(1) Bending stress in a grab bar or seat induced by the maximum bending moment from the application of 250 lbf (1112N) shall be less than the allowable stress for the material of the grab...
-
Section 36.406(f) Assembly Areas (Section-by-Section Analysis)
The Department has become aware that a growing trend in the design of large sports facilities is to provide wheelchair seating on removable platforms that seat four or more wheelchair users...
-
M301 Diagnostic Equipment Used by Patients in Supine, Prone, or Side-Lying Position
[See subsections ...]
