This video shows the use of Guldmann Ceiling lifts and slings in bariatric care. Watch more videos on http://www.youtube.com/vguldmann
Search Results "Patient Seated in Wheelchair"
- Guldmann Bariatric Care Solutions
-
Door Maneuvering Clearance
This exception derives from the original ADAAG and was intended to apply to those types of patient rooms where patients are typically transported in and out by hospital staff....
- American Specialties Surface Mounted Seat Cover Dispenser 0477-SM
-
5.9 Standing Support for Equipment Used by Patients in a Standing Position
5.9 Standing Support for Equipment Used by Patients in a Standing Position....
-
Clear Floor and Turning Space Inside Examination Rooms
must be able to approach the exam table and any other elements of the room to which patients have access....
-
M302.2.5 Unobstructed Transfer
Each transfer side complying with M302.2.4 shall provide unobstructed access to transfer surfaces. EXCEPTIONS: 1. Obstructions no more than 3 inches (75 mm) deep shall be...
-
F223.1 General
In licensed medical care facilities and licensed long-term care facilities where the period of stay exceeds twenty-four hours, patient or resident sleeping rooms shall be provided in accordance...
-
Hold and Release of Tickets for Accessible Seating
luxury boxes, club boxes, suites, and seats the venue holds back when declaring a sell-out); or when all non-accessible seats in a particular seating section have been sold, unsold accessible...
-
M305.2.4.2 Non-Circular Cross Section
Transfer supports with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (100 mm) minimum and 4.8...
-
5.1.3 Transfer Surface Low Height Options for M301 and M302
5.1.3 Transfer Surface Low Height Options for M301 and M302 The Committee did not agree on a final low height recommendation. Rationale for final recommendation (more detail...
-
5.1.3 Transfer Surface Low Height
5.1.3 Transfer Surface Low Height. No agreement on final low height
-
5.1.2 Transfer Surface High Height
5.1.2 Transfer Surface High Height. The transfer surface should have an adjustable height range with an upper height measuring at least 25 inches.
-
5.1.1 Transfer Surface Height Adjustability
5.1.1 Transfer Surface Height Adjustability. The transfer surface should have an adjustable height in small virtually continuous increments.
-
382.65 What are the requirements concerning on-board wheelchairs?
In aircraft with more than 60 passenger seats, carriers must provide an onboard wheelchair if the aircraft has an accessible lavatory....
- American Standard Commercial Toilet Seat for Baby Devoro Bowls
-
12162(a)(3)(A)(i)(II)
(II) to fold and store wheelchairs (to accommodate individuals who wish to transfer to coach seats) equal to not less than one-half of the number of single-level rail passenger coaches in...
- AJW Architectural Products U852 Dual Stall Seat Cover Dispenser - Partition Mounted
-
Section 35.151(g) Assembly areas (Section-by-Section Analysis)
In addition, the Department has revised the phrase ‘‘wheelchair and companion seating locations'' to ‘‘wheelchair spaces and companion seats.''...
-
M301.3 Transfer Supports
Height: Located no less than 6 inches (150 mm) and no more than 19 inches (482 mm) above the patient support surface Horizontal Distance from Transfer Surface: No more than 3 inches (...
-
Openings, Width and Length of Wheelchair Space
Openings, Width and Length of Wheelchair Space Openings and the width and length of wheelchair spaces need to be considered in relation to each other....
- Hill-Rom Liko® M220 / M230 Mobile Lift, Senior Video
- Hill-Rom Liko® M220 / M230 Mobile Lift, Pediatric Video
-
M301.1 General (Section-by-Section Analysis)
The MDE NPRM proposed that all diagnostic equipment used by patients in a supine, prone, or side-lying position must comply with the technical requirements of proposed section M301....
-
M301.4 Lift Compatibility
Diagnostic equipment shall be usable with portable patient lifts and, when in use with such lifts, shall comply with M301.4.1 or M301.4.2....