All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
Search Results "Head End Wall"
-
104.1.1 Construction and Manufacturing Tolerances
-
104.1.1 Construction and Manufacturing Tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
711.3.1 Through penetrations
Through penetrations of fire-resistance-rated walls shall comply with Section 711.3.1.1 or 711.3.1.2....
-
2.2.4 Maneuverability
tasks: • 90-degree turn, • 180-degree turn with no restrictions on length of the maneuver, • 180-degree with a center barrier, • 360-degree rotation within a space with four walls...
-
Clear Ground Space [1011.2]
Outdoor rinsing showers 60 by 60 inches centered on the shower heads....
-
Olympia i2 Single Handle Pull-Down Kitchen Faucet K-5020
Single Handle Pull-Down Kitchen Faucet Lever Handle Pull-Down Head with 2 Spray Patterns Swivel 360° 7-5/8″ Reach, 8-5/8″ From Deck to Aerator Ceramic...
-
Olympia i2 Single Handle Pull-Down Kitchen Faucet K-5025
Single Handle Pull-Down Kitchen Faucet Lever Handle Pull-Down Head with 2 Spray Patterns Swivel 360⁰ 7-5/8″ Reach, 8-3/4″ From Deck to Aerator Ceramic...
-
11B-610.3.1 Rectangular seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....
-
ADA Title II Technical Assistance Manual 1994 Supplement
These supplements are to be inserted, as appropriate, at the end of each chapter of the Manual....
-
Meeting ANSI Standard S12.60 Requirements
the wall height increases above ten feet....
-
Guardian Barrier-Free Safety Station with WideArea™ Eye/Face Wash GBF1909PCC
Shower head and pull rod are extended for improved access. Bowl is lowered and extended to permit access by wheelchair user....
-
30.1 Q. Would it be acceptable to use removable base cabinets beneath a wall-hung lavatory where a parallel approach is not possible?
A. Yes. The space under and around the cabinet should be finished prior to installation. For example, the tile or other floor finish must extend under the removable base cabinet.
-
SafePath SafeShower™ Ramp Transitions
[Some custom rubber product applications may be substituted] These SafeShowerTM ramps come with a built-in side approach or can be ordered with the flares or mitered ends removed for...
-
Recessed Doors and Gates: ADA Standard Section 404.2.4.3
Section 404.2.4.3 covers the current ADA Standards for maneuvering clearances at recessed doors and gates.
-
Alteration
restoration, resurfacing of circulation paths or vehicular ways, changes or rearrangement of the structural parts or elements, and changes or rearrangement in the plan configuration of walls...
-
11B-903.6 Structural strength
Benches shall be affixed to the wall or floor....
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware. ◼...
-
11B-201.3 Temporary and permanent structures
facilities covered by these requirements include, but are not limited to, reviewing stands, temporary classrooms, bleacher areas, stages, platforms and daises, fixed furniture systems, wall...
-
11B-903.6 Structural strength
Benches shall be affixed to the wall or floor....
-
11B-201.3 Temporary and permanent structures
facilities covered by these requirements include, but are not limited to, reviewing stands, temporary classrooms, bleacher areas, stages, platforms and daises, fixed furniture systems, wall...
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware. ◼...
-
§ 37.91(d)
(d) Unless not practicable, a person providing intercity rail transportation shall place an accessible car adjacent to the end of a single level dining car through which an individual who...
-
11. Gap
Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so the arm...
-
1k
Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so the arm...
