Where the floor at the entrance to the camp shelter is elevated above the ground surface, the floor shall be 17 (430 mm) high minimum to 19 inches (485 mm) high maximum measured from the...
Search Results "Road Surface Treatment"
Commonly Searched Documents
-
5.1.5 Floor Height
-
(2) Transfer Surface Location for Diagnostic Equipment Used in the Seated Position
Transfer onto these types of diagnostic equipment must be made from either long side, similar to the side transfer surface described above....
-
Maintenance
Maintenance Maintenance is one of the greatest factors affecting the accessibility of the surfaces in the sample. ...
-
§ 38.95(b)(6) Platform surface
(6) Platform surface. The lift platform surface shall be free of any protrusions over 1/4 inch high and shall be slip resistant....
- ACCESSMAT® - EN - Beach accessibility mats
-
I. Introduction to the Study
In addition, the ground surface must meet the ASTM F1951‒99 Standard Specification for Determination of Accessibility of Surface Systems Under and Around Playground Equipment. ...
- Sears Brands, LLC Craftsman 10 in. Digital LaserTrac® Level
- Husky 10" Multi-Function Standard Digital Level
-
Pemko 193 Slip resistance
Hello ETA, I see that you can ask for slip resistance by adding a coating to the Pemko 193 plate. Any experience with this application? Is this a permanent slip resistance or...
- Steelcase Series 5 Height-Adjustable Work Surface
-
ADA Gap Tool
ADA Gap Tool This handy tool was developed by Evan Terry Associates to assist its surveyors in measuring gaps in ground or floor surfaces....
-
3.3 Guidance on the Visual Properties of Detectable Warnings
Two relatively dark surfaces may provide high luminance contrast, but on asphalt or other dark sidewalk surfaces (with reflectance less than 10 percent) high contrast is not always a good...
- Steelcase Series 3 Height-Adjustable Work Surface with Crank
-
804.6.5.2 Bottom-Hinged Door Ovens
Bottom-hinged door ovens shall have the work surface required by 804.3 positioned adjacent to one side of the door....
-
804.6.5.2 Bottom-Hinged Door Ovens
Bottom-hinged door ovens shall have the work surface required by 804.3 positioned adjacent to one side of the door....
-
11B-1008.2.6.2 Use zones
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition)....
-
11B-1008.2.6.2 Use zones
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition)....
-
11B-1008.2.6.2 Use zones
Ground surfaces located within use zones shall comply with ASTM F 1292 (1999 edition or 2004 edition)....
-
M305.2.5 Surface Hazards
Transfer supports and surfaces adjacent to transfer supports shall be free of sharp or abrasive components and shall have eased edges....
-
804.6.5.1 Side-Hinged Door Ovens
Side-hinged door ovens shall have the work surface required by 804.3 positioned adjacent to the latch side of the oven door....
-
804.6.5.1 Side-Hinged Door Ovens
Side-hinged door ovens shall have the work surface required by 804.3 positioned adjacent to the latch side of the oven door....
-
11B-804.6.5.2 Bottom-hinged door ovens
Bottom-hinged door ovens shall have the work surface required by Section 11B-804.3 positioned adjacent to one side of the door....
-
Tread
Tread—The portion of a trail, outdoor recreation access route, or beach access route where traffic moves (for pedestrian routes, this is the walking surface)....
-
11B-804.6.5.2 Bottom-hinged door ovens
Bottom-hinged door ovens shall have the work surface required by Section 11B-804.3 positioned adjacent to one side of the door....