, or side-lying position (see Figure 5.4.1.1)....
Search Results "Pull Side"
Filters
Commonly Searched Documents
-
5.3.2.1 Transfer Sides Recommendation for Stretchers
-
Locating Controls & Devices: Percent of People Who Can Reach the Matrix Cell Indicated While Holding No Weight - Side Approach Scooter
These data depict the reaching abilities of scooter users represented as the percentage of users expected to reach to a target location in the lateral or sideways reach direction...
-
Why is a top landing required at curb ramps if side flares are provided?
A landing at least 36” long at the top of curb ramps provides room to approach or exit ramps and turn without encountering compound slopes of flared sides....
-
11B-404.2.7 Door and gate hardware
Handles, pulls, latches, locks, and other operable parts on doors and gates shall comply with Section 11B-309.4....
-
Locating Controls & Devices: Percent of People Who Can Reach the Matrix Cell Indicated While Holding 5 lb Weight - Side Approach Scooter
These data depict the reaching abilities of scooter users represented as the percentage of users able to retrieve and place a 5 lb object on a target shelf in the lateral or...
-
Maximum side reach ranges. (Section-by-Section Analysis)
Reach ranges apply to a variety of building elements, including light switches, key pads, electrical outlets, fire alarm pulls, card readers, thermostats, elevator controls, pay phones,...
-
11B-404.2.4 Maneuvering clearances
Maneuvering clearances shall extend the full width of the doorway and the required latch side or hinge side clearance. Exception: Reserved....
-
11B-404.2.4 Maneuvering clearances
Maneuvering clearances shall extend the full width of the doorway and the required latch side or hinge side clearance. Exception: Reserved....
-
Side Reach [§308.3]
Side Reach [§308.3] The range for side reach, like forward reach is 15” to 48” if unobstructed....
-
11B-404.2.4 Maneuvering clearances
Maneuvering clearances shall extend the full width of the doorway and the required latch side or hinge side clearance. [Safe Harbor only applies to existing primary entrances.]...
-
Door and Gate Hardware: ADA Standard Section 404.2.7
Section 404.2.7 covers the current ADA Standards for door and gate hardware.
-
Floor and Ground Surfaces: ADA Standard Section 503.4
Section 503.4 covers the current ADA Standards for the floor and ground surfaces at passenger loading zones.
-
RV Parking Spaces Within Camping Units With Mobility Features and RV Pull-Up Spaces at Dump Stations [F244.2.3.2.1 and F244.4]
RV parking spaces within camping units with mobility features and RV pull-up spaces at dump stations must comply with the technical requirements for width, surface, and slope of RV spaces...
-
407.12.2 Side Reach (Section-by-Section Analysis)
407.12.2 Side Reach (Section-by-Section Analysis) This section specifies proposed requirements for operable parts providing unobstructed or obstructed side reaches....
-
Side Approach
Side Approach Side reach depth is important to consider in the design and location of sinks....
-
Side Approach
Side Approach Where space is provided for a side approach, controls can be mounted at the heights allowed for side reaches....
-
Transfer Sides (M301.2.3 and M302.2.3)
M301.2.3 and M302.2.3 would require the transfer surface to be located so as to provide patients who use mobility devices the option to transfer onto the short side and the long side of...
-
Side Entry Openings, and Width and Length of Wheelchair Space
Side Entry Openings, and Width and Length of Wheelchair Space If the wheelchair space can only be entered from the side, the ride must be designed to permit sufficient turning space for...
-
b. Transfer Surface Location
The MDE NPRM proposed the same location and transfer sides of the transfer surface for diagnostic equipment used by patients in the supine, prone, or side-lying position (M301) and diagnostic...
-
604.5.1 Side Wall
604.5.1 Side Wall....
-
Side Approach and Reach
[See subsections ...]
-
11B-604.8.2.2 Doors
A door pull complying with Section 11B-404.2.7 shall be placed on both sides of the door near the latch....
-
11B-604.8.2.2 Doors
A door pull complying with Section 11B-404.2.7 shall be placed on both sides of the door near the latch....