Product Specifications Number 69 Dimensions 3" x...
Search Results "Recreational Surfacing"
-
Don-Jo Mfg., Inc. Push Plate 69
-
Hager Companies Door Protection Plate 214S
Door Protection Plate 214S 0.125" gauge with 4-sided bevel Materials: - Plastic Laminate NFPA Notes: - Self-adhesive tape available on all plates - Spanner head...
-
1002.4.4.3 Permitted Protrusions in Wheelchair Spaces
protrude a distance of 6 inches (150 mm) maximum along the front of the wheelchair space, where located 9 inches (230 mm) minimum and 27 inches (685 mm) maximum above the floor or ground surface...
-
11B-902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (762 mm) maximum above the finish floor or ground.
-
11B-902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (762 mm) maximum above the finish floor or ground.
-
Development of Surface Roughness Standards for Pathways Used by Wheelchair Users: Final Report
Development of Surface Roughness Standards for Pathways Used by Wheelchair Users: Final Report December 2014 Human Engineering Research Laboratories VA Pittsburgh Healthcare System...
-
Mirror Height
The guidelines specify that accessible mirrors be mounted so that the bottom edge of the reflecting surface is no higher than 40 inches (603.3)....
-
Passing Spaces [1016.4]
Also, consider providing a minimum clear width of 60 inches if the ORAR is a boardwalk or otherwise not at the same level as the adjoining ground surface or if the edge is bordered by timbers...
-
Material Characteristics (slide 6)
Matte finishes (slide 6) are always better than specular surfaces or polished granite. And that can be columns, and it can even be lighting fixtures....
-
National Trail Surfaces Study Final Report
National Trail Surface Study Final Report February 2014 Staff Liaison Bill Botten U.S....
-
11B-606.5 Exposed pipes and surfaces
There shall be no sharp or abrasive surfaces under lavatories and sinks....
-
11B-606.5 Exposed pipes and surfaces
There shall be no sharp or abrasive surfaces under lavatories and sinks....
-
§301(7)(L)
A gymnasium, health spa, bowling alley, golf course, or other place of exercise or recreation....
-
Inpro Corporation JointMaster® AR Series Seal Expansion Joint Systems
, and chemicals Heat weldable for watertight seams Industry unique design creates crisp sightline and incorporates ribs on side faces to aid in pooling epoxy and adding surface...
-
T302.1 General
Walking surfaces in non-rail vehicles shall comply with T302. EXCEPTION: Walking surfaces on lifts shall not be required to comply with T302....
-
1016.7.1 Maximum Running Slope and Segment Length
The running slope of any segment of an outdoor recreation access route shall not be steeper than 1:10 (10%). ...
-
1016.7.1 Maximum Running Slope and Segment Length
The running slope of any segment of an outdoor recreation access route shall not be steeper than 1:10 (10%)....
-
11B-804.3 Kitchen work surface
In residential dwelling units required to comply with Section 11B-809, at least one 30 inches (762 mm) wide minimum section of counter shall provide a kitchen work surface that complies...
-
11B-804.3 Kitchen work surface
In residential dwelling units required to comply with Section 11B-809, at least one 30 inches (762 mm) wide minimum section of counter shall provide a kitchen work surface that complies...
-
1002.4.4.2 Side Entry
Where wheelchair spaces are entered only from the side, amusement rides shall be designed to permit sufficient maneuvering clearance for individuals using a wheelchair or mobility...
-
1002.4.5 Ride Entry
Openings providing entry to wheelchair spaces on amusement rides shall be 32 inches (815 mm) minimum clear.
-
11B-1002.4.5 Ride entry
Openings providing entry to wheelchair spaces on amusement rides shall be 32 inches (813 mm) minimum clear.
-
1016.8 Resting Intervals
Resting intervals shall comply with 1016.8.
-
1016.8.1 Length
The resting interval length shall be 60 inches (1525 mm) long minimum.
