(9) In stations covered by this section, rail-to-platform height in new stations shall be coordinated with the floor height of new vehicles so that the vertical difference, measured when...
Search Results "Measuring Instrument"
Filters
Commonly Searched Documents
-
10.3.1(9)
-
Accessible Pathway & Corridor: Minimum Clear Floor Space Required for 360-degree Turn
Findings from the Anthropometry of Wheeled Mobility Study indicate that a square space of at least 160 x 160 cm (63 in.) was required for 50% of the manual wheelchair users measured in this...
-
Accessible Pathway & Corridor: Minimum Clear Width Required for 90-degree Turn
Findings from the Anthropometry of Wheeled Mobility Study indicate that a width of at least 85 cm (33 in.) was required for 50% of the manual and power wheelchair users measured in this...
-
Clearance in Base (M301.4.1 and M302.4.1)
M301.4.1 and M302.4.1 would require the clearance in the base to be 44 inches wide minimum, 6 inches high minimum measured from the floor, and 36 inches deep minimum measured from the edge...
-
11B-903.4 Back support
Back support shall be 2½ inches (64 mm) maximum from the rear edge of the seat measured horizontally. [2010 ADAS] 903.4 Back Support....
-
11B-903.4 Back support
Back support shall be 2½ inches (64 mm) maximum from the rear edge of the seat measured horizontally. [2010 ADA Standards] 903.4 Back Support....
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
Cross Slope
Measurements, absent live loads, are to be made from a static condition (i.e., absence of movement that results from wind, waves, etc.)....
-
804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
T505.3 Location of Operable Parts
Operable parts shall be located adjacent to the toe end of the clear space or shall be located no more than 10 inches (255 mm) measured from the centerline of the long dimension of the clear...
-
Treads & Risers
[ADA Stds. 4.9] Yes __ No __ N/A __ Comments: ___________________________________________ ...are all stair treads the same depth (at least 11" deep), measured riser to riser, to prevent...
-
Running Slope
In other words, the slope is the difference in elevation from the beginning to the end of a part of a trail, outdoor recreation access route, or beach access route, measured in the direction...
-
Door Closers [4.13.10]
requires that the sweep period of the closer be adjusted so that from an open position of 70 degrees, the door will take at least 3 seconds to move to a point 3 inches from the latch, measured...
-
§ 38.153(c)(1)
(1) Doors shall have a minimum clear width when open of 30 inches (760 mm), measured from the lowest step to a height of at least 48 inches (1220 mm), from which point they may taper to...
-
Access-Able Designs Portable Clamp-On Tub Seat SH-426
Measures 26.5" W x 15" D. Custom sizes available. 5 year warranty....
-
Bobrick Recessed Toilet Tissue Dispenser B-6677
Single-roll model measure 6 1⁄8" W x 6 1⁄8" H (155 x 155mm)....
-
Bobrick Recessed Toilet Tissue Dispenser B-667
Single-roll model measure 6 1⁄8" W x 6 1⁄8" H (155 x 155mm)....
-
Access-Able Designs Shower Transfer Bench SH-400-2SDL
Measures 32" W x 15" D x 22.5" D. Complies w/ ADA 4.21.3 when properly installed 5 year warranty....
-
F103 Modifications and Waivers
accessibility standards for buildings and facilities covered by the Architectural Barriers Act on a case-by-case basis, upon application made by the head of the department, agency, or instrumentality...
-
Summary of the project
that represent the following materials that may be used for exterior surfaces were invited and encouraged to participate to develop industry standard tolerances, installation methods, and measurement...
-
Q13: Are the provision and implementation of a health plan developed prior to the Amendments Act sufficient to comply with the FAPE requirements as described in the Section 504 regulation?
For example, before the Amendments Act, a student with a peanut allergy may not have been considered a person with a disability because of the student's use of mitigating measures (e.g.,...
-
Section 37.151 Waiver for Undue Financial Burden
Generally, the section allows an entity to request a wavier at any time it determines that it will not be able to meet a five-year phase-in or make measured progress toward its full compliance...
-
804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
