Specifically, the Committee recommended allowing base supports to be a maximum of 1½ inches high and allowing an additional sloped region above the base support at a depth of 25 inches from...
Search Results "Maximum Reach Depth"
-
b. Exception for Base Support Allowance and Unobstructed Knee and Toe Space
-
M302.4.2 Clearance Around Base
The width of the base permitted within this clearance shall be 26 inches (660 mm) wide maximum at the edge of the examination surface and shall be permitted to increase at a rate of 1 inch...
-
M301.4.2 Clearance Around Base
The width of the base permitted within this clearance shall be 26 inches (660 mm) wide maximum at the edge of the examination surface and shall be permitted to increase at a rate of 1 inch...
-
Technical Memorandum TM 2012-06 Wading Pools
will defer to the following definition contained in the Texas Administrative Code, Title 25, Part 1, §265.182(157) based on 201.1: 265.182 (157) Wading Pool – A Class D pool that has a maximum...
-
803.5 Coat Hooks and Shelves
Coat hooks provided within the room shall be located within one of the reach ranges specified in 308....
-
11B-604.8.3 Coat hooks and shelves
Coat hooks shall be located within one of the reach ranges specified in Section 11B-308....
-
604.8.3 Coat Hooks and Shelves
Coat hooks shall be located within one of the reach ranges specified in 308....
-
803.5 Coat Hooks and Shelves
Coat hooks provided within the room shall be located within one of the reach ranges specified in 308....
-
11B-704.4.1 Height
wheelchair accessible telephone because the required 34 inches (865 mm) minimum keypad height can causes the highest operable part of the telephone, usually the coin slot, to exceed the maximum...
-
11B-704.4.1 Height
wheelchair accessible telephone because the required 34 inches (865 mm) minimum keypad height can causes the highest operable part of the telephone, usually the coin slot, to exceed the maximum...
-
407.4.6.1 Location
Controls shall be located within one of the reach ranges specified in 308. EXCEPTIONS: 1....
-
11B-407.4.6.1 Location
Controls shall be located within one of the reach ranges specified in Section 11B-308. Exceptions: 1. ...
-
11B-407.4.6.1 Location
Controls shall be located within one of the reach ranges specified in Section 11B-308. Exceptions: 1....
-
M302.4.1 Clearance in Base
Where the width of the examination surface is less than 36 inches (915 mm), the clearance depth shall extend the full width of the equipment....
-
M301.4.1 Clearance in Base
Where the width of examination surfaces is less than 36 inches (915 mm), the clearance depth shall extend the full width of the equipment....
-
M302.4.1 Clearance in Base
Where the width of the examination surface is less than 36 inches (915 mm), the clearance depth shall extend the full width of the equipment....
-
M301.4.1 Clearance in Base
Where the width of the examination surface is less than 36 inches (915 mm), the clearance depth shall extend the full width of the equipment....
-
Exceptions Considered for Wheelchair Spaces on Raised Platforms
The exception to the minimum depth in M303.2.3 for wheelchair spaces entered from the front or rear would permit a portion of the 48 inch minimum depth of the wheelchair space that accommodates...
-
Southwestern Independent Living Center, Inc. (SILC) - Jamestown, NY
SILC provides services throughout Chautauqua County that will assist individuals with disabilities in reaching maximum independence and an enriched quality of life....
-
Adjustable height/gap protocol
This procedure was repeated until the largest horizontal distance was reached. The maximum and minimum heights attainable with the largest horizontal distance were recorded. ...
-
Grab Bars [4.20.4] and Controls [4.20.5]
Grab Bars [4.20.4] and Controls [4.20.5] Controls must be within reach from outside the tub and cannot interfere with the use of the grab bars....
-
BS8300:2001 Research
Footrest depth was measured from “front of wheelchair seat to the front of the toes” but an anatomical landmark on the toes was not identified and information was not provided about how...
-
5.4.2 Transfer Support Length for M301 and M302
The transfer support would extend horizontally the entire depth of the transfer surface and would be 15 inches minimum in length....
