Floor surfaces in elevator cars shall comply with Sections 11B-302 and 11B-303....
Search Results "Kitchen Work Surface"
Filters
Commonly Searched Documents
-
11B-409.4.2 Floor surfaces
-
11B-409.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Sections 11B-302 and 11B-303....
-
11B-409.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Sections 11B-302 and 11B-303....
-
11B-203.9 Employee workstations
Areas|_, 11B-302 _|Floor or Ground Surfaces|_, 11B-303 _|Changes in Level|_, and 11B-404.2.3 _|Doors, Doorways and Gates; Clear Width|_ unless exempted by other parts of this code. ...
-
R308.1.3.1 Surfaces
R308.1.3.1 Surfaces. The surfaces of boarding and alighting areas and boarding platforms shall comply with R302.7. Advisory R308.1.3.1 Surfaces....
-
505.8 Surfaces
505.8 Surfaces. Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....
-
Is there a minimum distance between changes in level?
span vertical changes greater than ½”, must have level landings and clearances at the tops and bottoms of each run to provide adequate separation and resting intervals between sloping surfaces...
-
11B-504.4 Tread surface
Stair treads shall comply with Section 11B-302. Changes in level are not permitted. Exception: Treads shall be permitted to have a slope not steeper than 1:48.
-
11B-504.4 Tread surface
Stair treads shall comply with Section 11B-302. Changes in level are not permitted. Exception: Treads shall be permitted to have a slope not steeper than 1:48.
-
Implications
surface. ...
-
1.2.1 Walks and other non - ramp surfaces
1.2.1 Walks and other non - ramp surfaces. When overall running slope for walks is measured according to Section 1.1.3 a recommended tolerance for running slope is +1%....
-
What does access for “approach, entry, and exit” to employee work areas require?
Access for individuals with disabilities to “approach, entry, and exit” employee work areas requires that the following be provided at a minimum: an accessible route to the work area, a...
-
T302 Walking Surfaces
[See subsections ...]
-
11B-804.6.2 Operable parts
All appliance controls shall comply with Section 11B-309. Exceptions: 1. Appliance doors and door latching devices shall not be required to comply with Section...
-
804.6.2 Operable Parts
All appliance controls shall comply with 309. EXCEPTIONS: 1. Appliance doors and door latching devices shall not be required to comply with 309.4. 2. Bottom-hinged appliance...
-
804.6.2 Operable Parts
All appliance controls shall comply with 309. EXCEPTIONS: 1. Appliance doors and door latching devices shall not be required to comply with 309.4. 2. Bottom-hinged...
-
804.6.2 Operable Parts
804.6.2 Operable Parts. All appliance controls shall comply with 309. EXCEPTIONS: 1. Appliance doors and door latching devices shall not be required to comply with 309.4. 2....
-
A4.34.6.7 OVENS
Countertop or wall-mounted ovens with side-opening doors are easier for people in wheelchairs to use. Clear spaces at least 30 in (760 mm) wide under counters at the side of ovens...
-
11B-804.6.2 Operable parts
All appliance controls shall comply with Section 11B-309. Exceptions: 1. Appliance doors and door latching devices shall not be required to comply with Section 11B-309.4. 2....
-
11B-804.6.2 Operable parts
All appliance controls shall comply with Section 11B-309. Exceptions: Appliance doors and door latching devices shall not be required to comply with Section...
-
Kickplates
Applied kickplates can help protect the door surface. If provided, it is recommended that they cover almost the full door width up to a height of 16 inches from the bottom edge....
-
4.5.4 Gratings
If gratings are located in walking surfaces, then they shall have spaces no greater than 1/2 in (13 mm) wide in one direction (see Fig. 8(g))....
-
4.5.4 GRATINGS
If gratings are located in walking surfaces, then they shall have spaces no greater than 1/2 in (13 mm) wide in one direction (see Fig. 8(g))....
-
505.8 Surfaces
Handrail gripping surfaces and any surfaces adjacent to them shall be free of sharp or abrasive elements and shall have rounded edges....