The truncated domes shall have a center-to-center spacing of 41 mm (1.6 in) minimum and 61 mm (2.4 in) maximum, and a base-to-base spacing of 17 mm (0.65 in) minimum, measured between the...
Search Results "Measuring Instrument"
-
R305.1.2 Dome Spacing
-
4.13.10* DOOR CLOSERS
then the sweep period of the closer shall be adjusted so that from an open position of 70 degrees, the door will take at least 3 seconds to move to a point 3 in (75 mm) from the latch, measured...
-
Cross Slope
The difference in elevation from edge to edge of an ORAR, trail, or beach access route measured perpendicular to the direction of travel. ...
-
Detail View – Accessible Round Set-Up
Measure from the back of one chair to the back of the chair directly behind it. Chairs must be set with the front edge of the chair at the edge of the table....
-
Running Slope (Grade)
The difference in elevation of a section of an ORAR, trail, or beach access route measured parallel to the predominant direction of travel. ...
-
2.4.1
2.4.1 Based on the methods for measuring compliance, define what remedial actions are acceptable when construction elements exceed tolerances....
-
1132A.3, Item 5
A pair of doors, manual or automatic, must have at least one leaf which provides a clear width of not less than 32 inches (813 mm), measured with the door positioned at an angle of 90 degrees...
-
1134A.6, Item 1.3
Other shower stall configurations shall measure at least 36 inches deep by 60 inches wide (914 mm by 1524 mm) with an entrance opening of at least 36 inches (914 mm) when a wall is installed...
-
§ 35.130(f)
(f) A public entity may not place a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures, such as the provision...
-
11B-703.5.8 Character spacing
Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces....
-
Inclusion Solutions Offset Door Hinge
The hinge measures 2" x 3-1/2" with a decorative, long lasting brass finish. (2" wide to wrap the trim)....
-
Character Specifications
For those with non-rectangular cross sections, the stroke thickness was specified to be 15% maximum of the character height (measured at the top of the cross section) and 10% to 30% (measured...
-
5.8.1.1 Clear Platform Size Recommendation
on wheeled mobility devices shown in the table below.4 Table 5.8.1.1 Wheelbase Measurements on Wheeled Mobility Devices Table !...
-
Employees
Once an employee is on the job, his actual performance is the best measure of ability to do the job....
-
§27.11(c)(2)(iii)
with official approval of recipient's management, any policies or practices that do not meet the requirements of this part according to a schedule or sequence that includes milestones or measures...
-
Clear Width [4.8.3]
The minimum dear width for ramps of 36 inches is measured between the leading edge of handrails. A maximum clear width is not specified....
-
Free-standing and Post-mounted Objects
This is based on standard measures for cane sweep. Objects with leading edges at or below 27 inches or above 80 inches can protrude any amount....
-
11B-703.8.7 Character spacing
Spacing shall be measured between the two closest points of adjacent low resolution VMS characters within a message, excluding word spaces....
-
Standards
methods for buildings - setting out and measurement - permissible measuring deviations ISO 4464 Tolerances for buildings - Relationship between the different types of deviations...
-
M303.2.2 Width
EXCEPTION: Wheelchair spaces located on raised platforms shall be permitted to be 32 inches (815 mm) wide minimum to a height of 4 inches (100 mm) measured from the platform surface....
-
C. Parking Slope
.: when measured as shown on the Tools & Techniques page , is the critical dimension 1/2" or less)?...
-
5.1.5 Floor Height
Where the floor at the entrance to the camp shelter is elevated above the ground surface, the floor shall be 17 (430 mm) high minimum to 19 inches (485 mm) high maximum measured from the...
-
2. b. i. Clear door openings
Clear openings of doorways with swinging doors shall be measured between the face of the door and the stop, with the door open 90° degrees.xiv...
