The size of transfer surfaces shall be measured from center points of their opposing sides....
Search Results "Measuring Instrument"
-
M302.2.3 Size
-
T402.8.1 Deployment to Roadways or to Curb Height Boarding and Alighting Areas
The running slope of ramps and bridgeplates used for deployment to the roadway or to curb-height boarding and alighting areas shall be 1:6 maximum, as measured to ground level with the non-rail...
-
§ 36.304(d)(4) Exemption for small facilities
For measures taken to comply with the barrier removal requirements of this section, existing facilities shall comply with the applicable requirements for alterations in § 36.402 and §§ 36.404...
-
7(2)(b)(vi)
(vi) Bathtubs and tub/showers located in the bathroom provide a clear access aisle adjacent to the lavatory that is at least 2'6" wide and extends for a length of 4'0" (measured from the...
-
1132A.3, Item 2
Swinging doors shall provide a net clear opening width of not less than 32 inches (813 mm), measured with the door or doors positioned at an angle of 90 degrees from the closed position....
-
1132A.3, Item 2
Swinging doors shall provide a net clear opening width of not less than 32 inches (813 mm), measured with the door or doors positioned at an angle of 90 degrees from the closed position....
-
§ 38.119(a)
(a) Any stepwell, or doorway with a lift, ramp or bridge plate, shall have, when the door is open, at least 2 foot-candles of illumination measured on the step tread, ramp, bridge plate...
-
§ 38.81(a)
(a) Any stepwell or doorway with a lift, ramp or bridge plate immediately adjacent to the driver shall have, when the door is open, at least 2 foot-candles of illumination measured on the...
-
1133A.2.1 Clear width
Kitchens shall have a minimum clear width measured between any cabinet, countertop or the face of any appliance (excluding handles and controls) that projects into the kitchen and the opposing...
-
604.9.3 Height
The height of water closets shall be 11 inches (280 mm) minimum and 17 inches (430 mm) maximum measured to the top of the seat....
-
XII. Examinations and Courses
In order to provide an examination in an accessible place and manner, a private entity must -- Assure that the examination measures what it is intended to measure, rather than reflecting...
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter...
-
III-4.4300 Standards to apply
Measures taken to remove barriers should comply with the ADA Accessibility Guidelines (ADAAG) contained in the appendix to the Department's rule....
-
Standardized Tests of Physical Fitness and Community Ambulation
Resting heart rate and energy consumption were measured with the subject seated or reclining on a couch. Heart rate was measured with a Polar heart rate monitor (Polar Vantage XL)....
-
What values are recommended for ground and floor surfaces along an accessible route?
In the study sponsored by the Access Board, laboratory measurements from a Kistler force plate and computer analysis of the gaits of persons with mobility impairments (including crutch users...
-
4.5 Weight Scales
In certain circumstances, such as setting chemotherapy dosages, weight is often a critical measurement....
-
Test Procedures
Accessibility Measures All surfaces were measured with the rotational penetrometer periodically over the first 6 months of exposure (Fig. 9)....
- Seton Economy Braille Signs - Women's Restroom with ISA
- Seton Economy Braille Signs - Men's Restroom with ISA
-
Disney Solitaire Hack mod apk Coins and Stars Android and iOS
The background music changed to an instrumental of "Hakuna Matata" just as I was about to beat it....
-
5 “G’s” Getting Access to Health Care for People with Physical Disabilities
Lemke, Rehabilitation Engineer, Rehabilitation Engineering Research Center on Accessible Medical Instrumentation, Madison, Wisconsin Christie Mac Donald MPP, Senior Policy Analyst, Center...
-
703.5.8 Character Spacing
Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces....
-
703.5.8 Character Spacing
Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces....