1 1/2" offset sink assemble with 149 brass flat grid strainer.
Search Results "Hinge Side Clearance"
Filters
Commonly Searched Documents
-
McGuire Manufacturing Co., Inc. PW1149WC: 1 1/2" Offset Sink 149 Flat Strainer
-
Zurn Industries Rigid Lavatory Enclosure - Vandal Gard
Rigid plastic lavatory enclosure 20" by 18" Conceals all piping, heaters, and other equipment below sink. 3-year warranty
-
McGuire Manufacturing Co., Inc. 155WC: Offset Lavatory Strainer
Furnished with heavy cast brass grid drain strainer, elbow and 1 1/4" 17GA seamless tubular offset tailpiece. ADA compliant. 8 3/4" x 5 1/8" OD.
-
McGuire Manufacturing Co., Inc. ProDrainWC: Lavatory Strainer Less Overflow
Offset strainer less overflow. Furnished with heavy brass grid drain strainer, heavy brass elbow and 1 1/4" 17GA seamless tubular brass offset tailpiece.
-
McGuire Manufacturing Co., Inc. 1151WC: Offset Strainer with 151 Basket Strainer
Offset sink strainer with chrome plated forged brass basket strainer with brass basket. 2 1/8" x 4 1/2" OD.
-
IPS Corporation Truebro® Lav Shield® Protective Lavatory Enclosure
Lav Shield® provides ADA-compliant undersink protection and meets requirements for wheelchair accessibility. Durable, single-piece construction conceals piping, electronic faucet...
-
McGuire Manufacturing Co., Inc. PW1000WC: 1 1/2" Offset Sink
1 1/2" offset sink assembly prewrapped.
-
McGuire Manufacturing Co., Inc. 1000WC: Offset Strainer - Offset Only
Offset sink strainer wheelchair offset. Allows up to 11" offset for wheelchair access use of most ADA sinks. The offset fits most 1 1/2" direct connect sink strainers including all...
-
McGuire Manufacturing Co., Inc. 1152WC: Offset with 152 Wide Top Strainer
Offset sink strainer with chrome plated wrought brass 4 1/2" wide top sink strainer. 1 3/4" x 4 1/2" OD.
-
McGuire Manufacturing Co., Inc. Heavy Finish Offset Lavatory Strainer
Classic McGuire wheelchair lavatory strainer. Furnished with heavy cast brass grid drain strainer, elbow and 1 1/4" 17GA seamless tubular offset tailpiece. PVD chrome finish. ADA...
-
Voting Area
Within the voting area there must be enough clearance for an individual with a disability to access and use all the voting equipment....
-
11B-406.5.10 Diagonal curb ramps
Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing....
-
M302.2.5 Unobstructed Transfer (Section-by-Section Analysis)
In the MDE NPRM the Access Board proposed that each transfer side provide unobstructed access to the transfer surface, with an exception to permit temporary obstructions as long as they...
-
M302.2.5 Unobstructed Transfer
Each transfer side complying with M302.2.4 shall provide unobstructed access to transfer surfaces. EXCEPTIONS: 1....
-
5.4.1.1 Transfer Support Location Recommendation for Stretchers
Rationale for the recommendation Patients access stretchers on either of the long sides rather than on its end (short side)....
-
11B-809.10.4 Sufficient maneuvering space
The clear maneuvering space shall be permitted to include knee and toe clearance under bathroom fixtures....
-
8. Gap
8. Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so...
-
11. Gap
11. Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so...
-
H. Drop-off Area Height
H. Is the height of the covered passenger pickup/drop-off area at least 9'−6" to allow vans with raised roofs to use such area? [ADA Stds. 4.6.5] Yes __ No __ N/A __ Comments:...
-
4.8.4(4)
(4) If a doorway is located at a landing, then the area in front of the doorway shall comply with 4.13.6.
-
4.3.5 HEAD ROOM
Accessible routes shall comply with 4.4.2.
