At each location where vertical actuation bars are provided the operable portion shall be located so the bottom is 5 inches (127 mm) maximum above the floor or ground surface and the top...
Search Results "Swing Grab Bar"
Filters
Commonly Searched Documents
-
11B-404.2.9 Door and gate opening force
-
Grab bar clearance
Have local authorities accepted one-piece dispensers in toilet compartments that are recessed behind the horizontal grab bars? These units stick out ¼" or so....
-
11B-408.3.2 Swinging doors
Swinging hoistway doors shall open and close automatically and shall comply with Sections 11B-404, 11B-407.3.2 and 11B-408.3.2....
-
Methodology
This study was approved by the University of Pittsburgh's Institutional Review Board and all participants provided informed consent before participating in any test procedures.
-
Minimum Clear Opening
Comment. The issue of minimum clear opening for doors was one of the most widely commented-upon design features of the guidelines. The majority of commenters representing the...
-
1018.4 Clear Width
The clear width of beach access routes shall be 60 inches (1525 mm) minimum. EXCEPTION: At dune crossings, the clear width of beach access routes that are not removable shall be...
-
Surface [1018.3]
The surface of beach access routes and resting intervals must be firm and stable. Sand is not a firm and stable surface. Additional information on firm and stable surfaces is...
-
Location [F248.3]
Beach access routes must coincide with or be located in the same general area as pedestrian access points that serve the beach.
-
Surface and Clear Tread Width on Beach Access Routes
A beach access route must have a firm, stable surface, and have a clear tread width of 60 inches (1,525 millimeters) minimum.
-
Slopes and Resting Intervals for Beach Access Routes
Running slope, also referred to as "grade," is the lengthwise slope of a beach access route, parallel to the direction of travel. Sections of beach access route of any length are...
-
6.6 Clear Width
The clear width of beach access routes shall be 60 inches (1525 mm) minimum. Exception: At dune crossings, the clear width of beach access routes that are not removable shall...
-
F248.3 Location
This section requires beach access routes to coincide with or be located in the same general area as pedestrian access points to the beach.
-
1018.4 Clear Width
The clear width of beach access routes shall be 60 inches (1525 mm) minimum. EXCEPTION: At dune crossings, the clear width of beach access routes that are not removable shall be...
-
General: ADA Standard Section 226.1
Section 226.1 of the ADA Standards covers information in the current ADA Standards on scoping requirements for dining surfaces and work surfaces.
-
11B-226.1 General
Where dining surfaces are provided for the consumption of food or drink, at least 5 percent of the seating spaces and standing spaces at the dining surfaces shall comply with Section...
-
11B-606.2 Clear floor space
A parallel approach complying with Section 11B-305 shall be permitted to a kitchen sink in a space where a cook top or conventional range is not provided and to wet bars. 2. Reserved...
-
Wikk Industries Inc. Bollard With Push Plate PART#BPRT126SMFT32D (630)
12”x6”x42” Tall, 7ga. Formed 304 Satin Stainless Steel US32D (630), Surface mount with concealed mounting base, 1 prep for INGRESS’R ® ADA switch (630), Welded Flat top. Shown on...
-
BEA Inc. LPR36 Series 36" Low Profile Push Plate
The LPR36 maximizes accessibility and independence for people with disabilities. The entire surface is “all-active” with four redundant membrane switches for consistent coverage. The...
-
SDC Bollard Post with Push Plate or Touch Panel
Alternative to wall mounted access control or switches for entry doors. Bollard post provide visibility and meet accessibility guidelines. Practical solution for surface mount or...
-
Wikk Industries Inc. PART# BPS SM-ING48 DB (710) with I36-3 Clear (628)
6”X6”X48” Tall, Dark Bronze Anodized Aluminum (710), Surface mount with concealed mounting base, 2 Preps for INGRESS’R® and card reader, Removable Black ABS Cap. **Customer can...
-
Wikk Industries Ingress'r Automatic Door Control
FEATURES: Weather resistant design allows interior or exterior application without adaptation UL® 15 amp. micro switch Crafted in clear anodized aluminum - will quote...
-
Wikk Industries Inc. PART#BPS SM-INGR CLEAR (628) with I36-3 CLEAR (628)
6”X6”X42” Tall, Clear Anodized Aluminum (628), Surface mount with concealed mounting base, 1 prep for INGRESS’R® ADA switch, Removable Black ABS cap Shown on the bollard- I36-3...
-
1607A.8 Loads on handrails, guards, grab bars, seats and vehicle barriers
1607A.8 Loads on handrails, guards, grab bars, seats and vehicle barriers....
