The ascent or descent of a trail segment expressed as a percentage of its length, which is the difference in elevation of a section of a trail measured parallel to the predominant direction...
Search Results "Mitigating Measures"
Filters
Commonly Searched Documents
-
Running Slope (Grade)
-
4.9.2 TREADS AND RISERS
Stair treads shall be no less than 11 in (280 mm) wide, measured from riser to riser (see Fig. 18(a)). Open risers are not permitted on accessible routes....
-
11B-703.8.7 Character spacing
Spacing shall be measured between the two closest points of adjacent low resolution VMS characters within a message, excluding word spaces....
-
TEST NO. 3 – UNUSUAL CHARACTERISTICS TEST
The original site characteristics result in a difference in finished grade elevation exceeding 30 inches (762 mm) and 10 percent measured between an entrance and all vehicular or pedestrian...
-
5.7.1 Lift Compatibility Clearance in Base for M301
The base of the equipment shall provide a clearance 44 inches wide minimum, 6 inches high minimum measured from the floor, and 36 inches deep minimum measured from the edge of the examination...
-
11B-604.7 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 _|Operation|_ and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the...
-
3-D Shape Digitization
3-D Shape Digitization Currently in the forefront of measuring methodology for anthropometric studies is 3-D shape digitization....
-
11B-233.3.1.2.6.4 Test number three, unusual characteristics test
The original site characteristics result in a difference in finished grade elevation exceeding 30 inches (762 mm) and 10 percent measured between an entrance and all vehicular or pedestrian...
-
Diversified Woodcrafts Mobile Lab Station with flat top 4352KF
Wheelchair accessible from two sides, measures 32"W x 29"H. Inside drawers measure: 14.5"W x 19"D x 6"H. Dimensions: 72"L x 24"D x 33"H. Weight: 240 lbs....
-
1009.2.4 Seat Height
The height of the lift seat shall be designed to allow a stop at 16 inches (405 mm) minimum to 19 inches (485 mm) maximum measured from the deck to the top of the seat surface when in the...
-
ADA Gap Tool
ADA Gap Tool This handy tool was developed by Evan Terry Associates to assist its surveyors in measuring gaps in ground or floor surfaces....
-
502.6 Identification
Signs shall be 60 inches (1525 mm) minimum above the finish floor or ground surface measured to the bottom of the sign....
-
Side Reach [§308.3]
The maximum reach depth for this range is 10” measured from the available clear floor space....
-
§ 37.139(d)(5)
The plan shall include milestones for implementing phases of the plan, with progress that can be objectively measured yearly;...
-
11B-813.2.1.3 Height and operation
Adult changing table height shall be adjustable from 17 inches (432 mm) above the floor or ground to 38 inches (965 mm) above the floor or ground, as measured to the top of the changing...
-
Discussion
Are there measures that give you a sense of that dynamic function in vision? Response by Bob Massof: Well, there are measures....
-
A. Accessible Voting Program
Nothing in this Agreement limits the County from making ADA-compliant, permanent modifications to its polling place locations instead of providing temporary remedial measures or relocating...
-
14. Child welfare agencies have an obligation to ensure the health and safety of children. How can agencies comply with the ADA and Section 504 while also ensuring health and safety?
severity of the risk to the child; the probability that the potential injury to the child will actually occur; and whether reasonable modifications of policies, practices, or procedures will mitigate...
-
20. When an employee requests leave as a reasonable accommodation, may an employer provide an accommodation that requires him/her to remain on the job instead?
After receiving the employee's request for leave for the surgery, the employer proposes that it provide certain equipment which it believes will mitigate the effects of the disability and...
-
11B-703.5.8 Character spacing
Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces....
-
4.30.3 Character Height
The minimum height is measured using an upper case X. Lower case characters are permitted....
-
§1630.14(d)(2)(iv)(C)
the information will be shared, and the methods that the covered entity will use to ensure that medical information is not improperly disclosed (including whether it complies with the measures...
-
705.1.2 Dome Spacing
detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch (17 mm) minimum, measured...
-
11B-802.3.1 Alignment
The shoulder alignment point of the wheelchair space shall be measured 36 inches (914 mm) from the front of the wheelchair space....