(f) A public entity may not place a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures, such as the provision...
Search Results "Mitigating Measures"
Filters
Commonly Searched Documents
-
§ 35.130(f)
-
11B-703.5.8 Character spacing
Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces....
-
Standards
methods for buildings - setting out and measurement - permissible measuring deviations ISO 4464 Tolerances for buildings - Relationship between the different types of deviations...
-
Executive Summary
The structural anthropometric measurements required the measurement of the body and devices size at rest....
-
IDEA Center
and measurements of maneuvering clearances....
-
Employees
Once an employee is on the job, his actual performance is the best measure of ability to do the job....
-
§27.11(c)(2)(iii)
with official approval of recipient's management, any policies or practices that do not meet the requirements of this part according to a schedule or sequence that includes milestones or measures...
-
Clear Width [4.8.3]
The minimum dear width for ramps of 36 inches is measured between the leading edge of handrails. A maximum clear width is not specified....
-
Free-standing and Post-mounted Objects
This is based on standard measures for cane sweep. Objects with leading edges at or below 27 inches or above 80 inches can protrude any amount....
-
11B-703.8.7 Character spacing
Spacing shall be measured between the two closest points of adjacent low resolution VMS characters within a message, excluding word spaces....
-
11B-202.4 Path of travel requirements in alterations, additions and structural repairs
In order to mitigate existing barriers, it is first necessary to identify them....
-
Just Manufacturing Automatic Soap Dispenser
Pre-measured dispensing volume (1-1.5ml). Reservoir capacity 900ml - refillable. Sensor detection range adjustable....
-
Seton Parking Signs - Van Accessible with ISA
.063" Engineer Grade reflective aluminum to improve sign visibility at night Extend the life and performance of the sign by upgrading to Seton UltraTuff™ overlaminate Sign measures...
-
Seton Parking Signs - Blue Reserved Parking with ISA
.063" Engineer Grade reflective aluminum to improve sign visibility at night Extend the life and performance of the sign by upgrading to Seton UltraTuff™ overlaminate Sign measures...
-
Inclusion Solutions Blue Parking Stop
Steel installation anchors included Measures 72"L x 4"H x 6"W Weighs 30 lbs....
-
M301.4 Lift Compatibility
Compatibility M01.4.1 Clearance in Base Proposed requirement: The base of the equipment shall provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured...
-
A4.5.1 General
While the dynamic coefficient of friction during walking varies in a complex and non-uniform way, the static coefficient of friction, which can be measured in several ways, provides a close...
-
11B-705.1.1.2 Dome spacing
detectable warning surface shall have a center-to-center spacing of 2.3 inches (58 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch (16.5 mm) minimum, measured...
-
703.3.1 Dimensions and Capitalization
Table 703.3.1 Braille Dimensions Measurement Range Minimum in Inches Maximum in Inches Dot base diameter 0.059 (1.5 mm) to 0.063 (1.6 mm)...
-
§35.130(f) (Section-by-Section Analysis)
Paragraph (f) provides that a public entity may not place a surcharge on a particular individual with a disability, or any group of individuals with disabilities, to cover any costs of measures...
-
1017.5 Tread Obstacles
This section requires obstacles to not exceed 1/2 inch in height measured vertically to the highest point....
-
Energy Consumption During Ambulation
Measurements were recorded for subjects walking on the Straight and Turning Courses....
-
11B-705.1.2.2.2.2 Two entrance/exit points
Where the turning space has two entrance/exit points other than the sloped ramp segments, detectable warnings shall be 36 inches (914 mm) deep at both entrance/ exit points, as measured...
-
1132A.3 Width and height of interior doors and secondary exterior doors
Swinging doors shall provide a net clear opening width of not less than 32 inches (813 mm), measured with the door or doors positioned at an angle of 90 degrees from the closed position....
