A pair of doors, manual or automatic, must have at least one leaf which provides a clear width of not less than 32 inches (813 mm), measured with the door positioned at an angle of 90 degrees...
Search Results "Door Hardware"
-
1132A.3, Item 5
-
1132A.3, Item 5
A pair of doors, manual or automatic, must have at least one leaf which provides a clear width of not less than 32 inches (813 mm), measured with the door positioned at an angle of 90 degrees...
-
Stanley Hardware RP9402 Door Closer
Product Overview Used on entry doors and doors between the house and garage Designed for use on out swinging or in swinging wood or metal doors up to 1-3/8" thick Hold open feature...
-
11B-213.3.1.2 Toilet compartments with urinal compartments
At all compartments not required to comply with Section 11B-604.8 or Section 11B-605.5, compartment doors shall be in-swinging and self-closing....
-
11B-213.3.1.2 Toilet compartments with urinal compartments
At all compartments not required to comply with Section 11B-604.8 or Section 11B-605.5, compartment doors shall be in-swinging and self-closing....
-
4.1.2(7)
(7) Doors: (a) At each accessible entrance to a building or facility, at least one door shall comply with 4.13....
-
Hager Companies Round Offset Pull 11
Round Offset Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2'' (64 mm) Clearance available on special order....
-
Door Clear Width
Door Clear Width Open the door 90 degrees, measure from the face of the door to the edge of the door stop....
-
703.4.2 Location
Where a tactile sign is provided at a door, the sign shall be located alongside the door at the latch side....
-
Rockwood Manufacturing Company 110 x 70B Pull Plate 8" CTC Pull 3-1/2" x 15" Plate
Material: Aluminum, Brass, Bronze, Stainless Steel Fastener: #6 x 5⁄8 OHSMS; 1⁄4 -20 x 2-1⁄4 Thru Bolt & Finish Washer (standard 1-3⁄4" door)....
-
Rockwood Manufacturing Company 11047 Series 47 Straight Single Bar Set 8" Pull CTC
T3 is the standard mounting method for Metal and Wood Doors. (See our mounting selections on this site.)...
-
Yale 1500 Series Traditional Exit Devices
Lever, knob, handle and pull trim designs offer variety and permit hardware balance throughout a building 2-point hex-key dogging for standard devices allows quiet push-pull door...
-
Are spring hinges and gravity hinges considered “closers” in determining the size of maneuvering clearances?
Some approaches require additional maneuvering clearances when a door or gate is equipped with a closer because of the additional force that must be counteracted in proceeding through doors...
-
H25
Is the clear width of the door at least 32 inches (measured between the face of the door and the edge of the opening) when the door is open 90 degrees?...
-
Floor or Ground Surface: ADA Standard Section 404.2.4.4
Section 404.2.4.4 covers the current ADA Standards for floor or ground surfaces at door maneuvering clearances.
-
Doors, Doorways, and Gates
Section 206.5 provides scoping requirements for doors, doorways, and gates....
-
1132A.3, Item 3
Swinging doors shall be capable of opening at least 90 degrees....
-
1132A.3, Item 3
Swinging doors shall be capable of opening at least 90 degrees....
-
11B-404.3.2 Maneuvering clearance
Clearances at power-assisted doors and gates shall comply with Section 11B-404.2.4....
-
11B-404.3.2 Maneuvering clearance
Clearances at power-assisted doors and gates shall comply with Section 11B-404.2.4....
-
11B-404.3.2 Maneuvering clearance
Clearances at power-assisted doors and gates shall comply with Section 11B-404.2.4....
-
ADAEZ Pro Plus Automatic Door Opener Installing the Door Decals Video
ADAEZ Pro Plus Automatic Door Opener Installing the Door Decals Video...
-
SECTION 1008 DOORS, GATES AND TURNSTILES
SECTION 1008 DOORS, GATES AND TURNSTILES [DSA-AC] In addition to the requirements of this section, means of egress, which provide access to, or egress from, buildings or facilities where...
-
Cal-Royal CR6000 Series Digital Touch Screen Door Lock
DOOR RANGES - 1 3/8" to 2" BACKSET - 2 3/4" Standard or 2-3/8" optional backset. LATCH FACEPLATE -Standard - 1 1/8" x 2 1/4" for 2-3/4" backset....
