Is the clear width of the door at least 32 inches (measured between the face of the door and the edge of the opening) when the door is open 90 degrees?...
Search Results "Door Hardware"
Filters
Commonly Searched Documents
-
H25
-
Hager Companies Round Offset Pull 11
Round Offset Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2'' (64 mm) Clearance available on special order....
-
SECTION 1008 DOORS, GATES AND TURNSTILES
SECTION 1008 DOORS, GATES AND TURNSTILES [DSA-AC] In addition to the requirements of this section, means of egress, which provide access to, or egress from, buildings or facilities where...
-
1132A.3, Item 3
Swinging doors shall be capable of opening at least 90 degrees....
-
1132A.3, Item 3
Swinging doors shall be capable of opening at least 90 degrees....
-
11B-404.3.2 Maneuvering clearance
Clearances at power-assisted doors and gates shall comply with Section 11B-404.2.4....
-
11B-404.3.2 Maneuvering clearance
Clearances at power-assisted doors and gates shall comply with Section 11B-404.2.4....
-
11B-404.3.2 Maneuvering clearance
Clearances at power-assisted doors and gates shall comply with Section 11B-404.2.4....
-
Floor or Ground Surface: ADA Standard Section 404.2.4.4
Section 404.2.4.4 covers the current ADA Standards for floor or ground surfaces at door maneuvering clearances.
-
Rockwood Manufacturing Company 110 x 70B Pull Plate 8" CTC Pull 3-1/2" x 15" Plate
Material: Aluminum, Brass, Bronze, Stainless Steel Fastener: #6 x 5⁄8 OHSMS; 1⁄4 -20 x 2-1⁄4 Thru Bolt & Finish Washer (standard 1-3⁄4" door)....
-
Automatic Door Break Out Openings
Automatic Door Break Out Openings. The 1991 Standards do not contain any technical requirement for automatic door break out openings....
-
Rockwood Manufacturing Company 11047 Series 47 Straight Single Bar Set 8" Pull CTC
T3 is the standard mounting method for Metal and Wood Doors. (See our mounting selections on this site.)...
-
SECTION 1132A DOORS
[See subsections ...]
-
SECTION 1132A DOORS
[See subsections ...]
-
Yale 1500 Series Traditional Exit Devices
Lever, knob, handle and pull trim designs offer variety and permit hardware balance throughout a building 2-point hex-key dogging for standard devices allows quiet push-pull door...
-
1132A.4.1 Thresholds
Thresholds at the primary entry and required exit doors shall be no higher than ½ inch (12.7 mm)....
-
404.3.2 Maneuvering Clearance
Clearances at power-assisted doors and gates shall comply with 404.2.4....
-
4.10.6* DOOR PROTECTIVE AND REOPENING DEVICE
Elevator doors shall open and close automatically....
-
404.3.2 Maneuvering Clearance
Clearances at power-assisted doors and gates shall comply with 404.2.4....
-
404.3.2 Maneuvering Clearance
Clearances at power-assisted doors and gates shall comply with 404.2.4....
-
11B-411.3.3 Reopening device
Elevator doors shall be provided with a reopening device complying with Section 11B-411.3.3 that shall stop and reopen a car door and hoistway door automatically if the door becomes obstructed...
-
Doorways at Landings [§405.7.5]
Doorways at Landings [§405.7.5] Required door maneuvering clearances can overlap ramp landings (it is advisable to locate the swing of doors outside ramp landings for greater safety)....
-
ADAEZ Pro Plus Automatic Door Opener Installing the Door Decals Video
ADAEZ Pro Plus Automatic Door Opener Installing the Door Decals Video...
-
Exit Doors: ADA Standard Section 216.4.1
Section 216.4.1 covers scoping requirements in the current ADA Standards for signs at exit doors.
