Round Pull Door Pull Materials: - Aluminum, brass, bronze, stainless steel Certification: - Meets ANSI A156.6 for J401 Pulls...
Search Results "Door Hardware"
-
Hager Companies Round Pull 10
-
1132A.3, Item 4
A nominal 32-inch (813 mm) clear opening provided by a standard 6-foot wide (1829 mm) sliding patio door assembly is acceptable....
-
1132A.3, Item 4
A nominal 32-inch (813 mm) clear opening provided by a standard 6-foot wide (1829 mm) sliding patio door assembly is acceptable....
-
Hager Companies Cast Pull 7N
Cast Door Pull Materials: - Aluminum, Brass, Bronze Options: - May be combined with a plate to make a pull plate Certification: - Meets ANSI A156.6 for J401 Pulls...
-
Hager Companies Cast Pull 5N
Cast Door Pull Materials: - Aluminum, brass, bronze, stainless steel Options: - May be combined with a plate to make a pull plate Certification: - Meets ANSI A156.6 for J401 Pulls...
-
Hager Companies Cast Pull 6N
Cast Door Pull Materials: - Aluminum, brass, bronze, stainless steel Options: - May be combined with a plate to make a pull plate Certification: - Meets ANSI A156.6 for J401 Pulls...
-
CRL Push Button Center Locks for Glass Doors 08 4210
08 4210 CRL Center Locks for Glass Doors For use with 1/2" (12 mm) Monolithic Tempered Glass Available in Two Sizes: 4" x 10" and 6" x 10" Choose From Three Types: Deadlatch,...
-
Re: 404.2.6 Doors in Series and Gates in Series
My understanding is that it was written to keep wheelchair users from having to fight two doors at once. ...
-
Hager Companies Round Offset Pull 11
Round Offset Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2'' (64 mm) Clearance available on special order....
-
Door Protective and Reopening Device [4.10.6]
Door reopening devices must be able to detect obstructions without contact; otherwise, they can disrupt the balance of people using crutches or canes....
-
Communication Access at Doors [§806.3.2, §809.5.5]
Communication Access at Doors [§806.3.2, §806.3.2] ETA Editor's Note This section title contains a typo, as it duplicates section number "806.3.2."...
-
Rockwood Manufacturing Company 110 x 70B Pull Plate 8" CTC Pull 3-1/2" x 15" Plate
Material: Aluminum, Brass, Bronze, Stainless Steel Fastener: #6 x 5⁄8 OHSMS; 1⁄4 -20 x 2-1⁄4 Thru Bolt & Finish Washer (standard 1-3⁄4" door)....
-
16.1 Q. Will a standard hung 32-inch door provide sufficient clear width to meet the requirements of the Fair Housing Act?
No, a 32-inch door would not provide a sufficient clear opening to meet the requirement for usable doors....
-
Rockwood Manufacturing Company 11047 Series 47 Straight Single Bar Set 8" Pull CTC
T3 is the standard mounting method for Metal and Wood Doors. (See our mounting selections on this site.)...
-
Guestroom Doors
Guestroom Doors Common Problem: Doors and doorways into and within all guestrooms and suites, including bathroom doors and doorways, do not allow 32 inches of clear opening width....
-
11B-604.8.1.1.3 Maneuvering space with end-opening door
In a wheelchair accessible compartment with a door located in the front wall or partition (facing the water closet), either in-swinging or out-swinging, a minimum 60 inches (1524 mm) wide...
-
11B-604.8.1.1.3 Maneuvering space with end-opening door
11B-604.8.1.1.3 Maneuvering space with end-opening door....
-
(1)(e)
Door latches and hardware should be operable with one hand and should not require tight grasping, pinching, or twisting of the wrist....
-
Closers
Closers Automated door closing is addressed by the ANSI/BHMA standards....
-
Yale 1500 Series Traditional Exit Devices
Lever, knob, handle and pull trim designs offer variety and permit hardware balance throughout a building 2-point hex-key dogging for standard devices allows quiet push-pull door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
11B-404.2.10 Door and gate surfaces
Swinging door and gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
A. Entry Doors
Do entry doors, connecting room doors, and interior doors (except doors to shallow closets) into and within all guestrooms and suites allow 32" clear passage width so persons who use wheelchairs...
