Can easily fold up against the wall when not in use. Product Specification The shower seat shall have a Brazilian Walnut back rest and seating surface....
Search Results "Back Wall"
-
Healthcraft Invisia ADA Serenaseat™ Folding Shower Seat
-
§ 37.42(e)(1)
) Except as provided in paragraph (e)(2) of this paragraph, any obstructions on a platform (mini-high platforms, stairwells, elevator shafts, seats etc.) shall be set at least six feet back...
-
§ 37.42(e)(1)
) Except as provided in paragraph (e)(2) of this paragraph, any obstructions on a platform (mini-high platforms, stairwells, elevator shafts, seats etc.) shall be set at least six feet back...
-
711.3.1 Through penetrations
Through penetrations of fire-resistance-rated walls shall comply with Section 711.3.1.1 or 711.3.1.2....
-
2.2.4 Maneuverability
tasks: • 90-degree turn, • 180-degree turn with no restrictions on length of the maneuver, • 180-degree with a center barrier, • 360-degree rotation within a space with four walls...
-
11B-809.9.3 Removable base cabinets
following conditions are met: a) base cabinets can be removed without the use of specialized tools or knowledge; b) the finish floor extends under the base cabinet; and c) the walls...
-
11B-809.9.3 Removable base cabinets
following conditions are met: a) base cabinets can be removed without the use of specialized tools or knowledge; b) the finish floor extends under the base cabinet; and c) the walls...
-
11B-610.3.1 Rectangular seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....
-
Toilet Compartment Access
Doors shall be located in the front partition or in the side wall or partition farthest from the water closet....
-
11B-609.3 Spacing
of 6 inches on either side of the inside corner between two adjacent wall surfaces....
-
11B-609.3 Spacing
of 6 inches on either side of the inside corner between two adjacent wall surfaces....
-
11B-609.3 Spacing
of the inside corner between two adjacent wall surfaces....
-
11. Gap
Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so the arm...
-
1k
Is the gap between the wall and the inside face of each grab bar exactly 1 1/2" to accommodate persons with disabilities who rest their forearms on the bars for stabilization so the arm...
-
4.4.4 Clear Floor or Ground Space
Shoulder alignment generally can be achieved by positioning the back of the bench so it is 8 inches (200 millimeters) closer to the outdoor recreation access route, trail, or beach access...
-
5.8.1.2.2 Single Ramped Entry – Edge Protection on the Platform and Platform Sides
A 2 inch high edge protection must be provided on the back of the platform, opposite the entry ramp and a minimum 2 inch high edge protection on the sides of the platform....
-
Controls and form elements
See ‘Agency Guide: Alternative text for links, controls and form elements’ (a link to the guide is provided in the back pages of this document) for. ...
-
11B-903.6 Structural strength
Benches shall be affixed to the wall or floor....
-
11B-903.6 Structural strength
Benches shall be affixed to the wall or floor....
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware. ◼...
-
Alteration
restoration, resurfacing of circulation paths or vehicular ways, changes or rearrangement of the structural parts or elements, and changes or rearrangement in the plan configuration of walls...
-
Recessed Doors and Gates: ADA Standard Section 404.2.4.3
Section 404.2.4.3 covers the current ADA Standards for maneuvering clearances at recessed doors and gates.
-
11B-201.3 Temporary and permanent structures
facilities covered by these requirements include, but are not limited to, reviewing stands, temporary classrooms, bleacher areas, stages, platforms and daises, fixed furniture systems, wall...
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware. ◼...