Where changes in level are permitted in floor or ground surfaces, they shall comply with 303. EXCEPTIONS: 1....
Search Results "Ground Surface"
-
303.1 General
-
203.9 Employee Work Areas
areas, or portions of employee work areas, other than raised courtroom stations, that are less than 300 square feet (28 m2) and elevated 7 inches (180 mm) or more above the finish floor or ground...
-
304.2 Floor or Ground Surfaces
Floor or ground surfaces of a turning space shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
4 - Best practices for construction observation
For large projects for where extensive accessible surfaces are required, early checking should be done to suggest needed adjustments to construction techniques....
-
Suggested accessibility guidelines for exterior concrete surfaces
The following tolerances may be applicable for exterior accessible surfaces....
-
305.2 Floor or Ground Surfaces
Floor or ground surfaces of a clear floor or ground space shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
3. Study Findings
-
4) Where the Standard is silent about changes in level
4) Where the Standard is silent about changes in level, such as 604.3 around a water closet or in a toilet compartment: Since there is no mention of the phrase "changes in level...
-
Acceptable Trail Surfacing Requirements
Trail surfaces are currently considered accessible only if the surfacing material is firm, stable, and slip-resistant and the trail has the engineered attributes of adequate width, moderately...
-
Floor and Ground Surfaces
This guide explains requirements in the ADA Standards for floor and ground surfaces. ...
-
Firmness, Stability, and Slip Resistance [§302.1]
Firmness, Stability, and Slip Resistance [§302.1] Accessible floor and ground surfaces must be stable, firm, and slip resistant....
-
Slip Resistance
Compliance with the standards requires specifying surface materials, textures, or finishes that prevent or minimize slipperiness under the conditions likely to be found on the surface....
-
Accessible - Changes in Level
Accessible - Changes in Level: Changes in level up to 1/4" may be vertical and without edge treatment. Changes in level between 1/4" and 1/2" shall be beveled with a slope no...
-
Surface Smoothness
The standards limit changes in level and openings in floor and ground surfaces, but they do not further address overall surface smoothness....
-
Openings [§302.3]
Openings [§302.3] Openings in ground and floor surfaces, such as grates, are limited in width to prevent passage of a ½” diameter sphere....
-
Common Questions (Floor and Ground Surfaces)
Common Questions
-
Must accessible surfaces be paved?
Concrete, asphalt, and other paved surfaces are more reliably compliant, but other materials, such as wood, and construction methods can be used to provide firm and stable surfaces. ...
-
What is the minimum level of slip resistance required by the standards?
The standards require ground and floor surfaces to be slip resistant, but they do not specify a minimum level of slip resistance or coefficient of friction. ...
-
Is there a minimum distance between changes in level?
span vertical changes greater than ½”, must have level landings and clearances at the tops and bottoms of each run to provide adequate separation and resting intervals between sloping surfaces...
-
302 Floor or Ground Surfaces
302 Floor or Ground Surfaces...
-
Polling places that cannot be remediated with temporary measures:
Parking & Sidewalks & Walkways: The parking lot and the walkway to the sidewalk are covered with grass and do not provide stable, firm, and slip resistant surfaces (1991 ADA Stds...
-
302.1 General
Floor and ground surfaces shall be stable, firm, and slip resistant and shall comply with 302. EXCEPTIONS: 1....
-
Surface and Size [§305.2 and §305.3]
Surface and Size [§305.2 and §305.3] Clear floor spaces must meet requirements for ground and floor surfaces, including criteria for firmness, stability, and slip resistance....
-
302.3 Openings
Openings in floor or ground surfaces shall not allow passage of a sphere more than ½ inch (13 mm) diameter except as allowed in 407.4.3, 409.4.3, 410.4, 810.5.3 and 810.10....