Penetrations of membranes that are part of a fire-resistance-rated horizontal assembly shall comply with Section 711.4.1.1 or 711.4.1.2....
Search Results "Comply With"
-
711.4.2 Membrane penetrations
-
302.2 Carpet
Carpet edge trim shall comply with 303. Advisory 302.2 Carpet....
-
404.2.4.2 Doorways without Doors or Gates
Doorways less than 36 inches (915 mm) wide without doors or gates, sliding doors, or folding doors shall have maneuvering clearances complying with Table 404.2.4.2....
-
Fishing piers and platforms. (Section-by-Section Analysis)
(An exception permits railings to comply, instead, with the model codes, which permit railings to be 42 inches high.) ...
-
Scope of Coverage
comments were received on the issue of which types of dwelling units should be subject to the Act's accessibility requirements, and the number or percentage of dwelling units that must comply...
-
Guidelines for Requirement 3
(1) For public and common use areas and entry doors to dwelling units, doors that comply with ANSI 4.13 would meet the requirements of §100.205(c)(2)....
-
Technical Memorandum TM 2013-19 Private Toilet and Bathing Rooms
Based on TAS 213.2 and TAS 213.3, private toilet and bathing rooms and the plumbing fixtures and accessories provided in these rooms shall comply with TAS 603 and all other applicable provisions...
-
11B-504.5 Nosings
While Chapter 10 may allow larger radius of curvature at the leading edge (nosing) of the tread, this radius must be no larger than ½ inch to comply with both Chapter 10 and Chapter 11B...
-
§35.164 Duties
If an action required to comply with this subpart would result in such an alteration or such burdens, a public entity shall take any other action that would not result in such an alteration...
-
11B-604.3.1 Size
Exception: In residential dwelling units complying with Section 11B-233.3.1.1, maneuvering space in front of the water closet shall be a minimum 60 inches (1524 mm) wide and 36 inches (...
-
Amusement rides. (Section-by-Section Analysis)
Thus, newly constructed and altered amusement rides shall comply with the 2010 Standards if the start of physical construction or the alteration is on or after 18 months from the publication...
-
7. Alternatives
The Board also considered requiring ICT to comply with the full set of functional performance criteria, which state in general terms the features of ICT that ensure its accessibility to...
-
Relationship to Other Laws
In addition, the title III regulation provides that part 36 does not affect the obligations of a recipient of Federal financial assistance to comply with the requirements of section 504...
-
Elevated Dune Crossings
Ensure the handrails are easy to grip and comply with all the other requirements in ABAAS, section 505....
-
1016.7.1 Maximum Running Slope and Segment Length
slope of a segment of an outdoor recreation access route is steeper than 1:20 (5%), the maximum length of the segment shall be in accordance with Table 1016.7.1, and a resting interval complying...
-
III-7.7000 Alterations
For instance -- 1) Section 4.1.6(3) contains a detailed set of special technical provisions for alterations to be applied where it is technically infeasible to comply with other provisions...
-
4.8.5* HANDRAILS
Handrails shall comply with 4.26 and shall have the following features: (1) Handrails shall be provided along both sides of ramp segments....
-
1018.7.1 Maximum Running Slope and Segment Length
Where the running slope of a segment of a beach access route is steeper than 1:20 (5%), the maximum length of the segment shall be in accordance with Table 1018.7.1, and a resting interval complying...
-
Other Requirements in the ADA Standards
Operable Parts Operable parts used by building occupants, including alarms pulls and hardware for fire extinguisher cabinets, must comply (§205, §309)....
-
§ 35.101 Purpose and broad coverage
The primary object of attention in cases brought under the ADA should be whether entities covered under the ADA have complied with their obligations and whether discrimination has occurred...
-
Signage
Signs should not be made of reflective materials such as brass, silver, gold, glass, or mirrored surfaces unless there is an additional properly located sign that complies with the Standards...
-
Drinking Fountains
b) Where more than one drinking fountain or water cooler is provided on a floor, 50% of those provided shall comply with 4.15 and shall be on an accessible route....
-
11B-504.5 Nosings
While Chapter 10 may allow larger radius of curvature at the leading edge (nosing) of the tread, this radius must be no larger than ½ inch to comply with both Chapter 10 and Chapter 11B...
-
11B-604.3.1 Size
Exception: In residential dwelling units complying with Section 11B-233.3.1.1, maneuvering space in front of the water closet shall be a minimum 60 inches (1524 mm) wide and 36 inches (914...