Along runs and landings, the minimum clear width must be measured between the leading edge of handrails....
Search Results "Tape Measure"
Commonly Searched Documents
-
Can handrails overlap ramp landings?
-
§ 38.31(b)
(b) Other stepwells and doorways, including doorways in which lifts or ramps are installed, shall have, at all times, at least 2 foot-candles of illumination measured on the step tread,...
-
B. Survey and Review of Polling Place Locations
The survey instrument will include: (1) measurements of each feature in the survey form (e.g., width of parking space, slope of curb ramp); (2) photographs of each element of the polling...
-
Character Specifications
For those with non-rectangular cross sections, the stroke thickness was specified to be 15% maximum of the character height (measured at the top of the cross section) and 10% to 30% (measured...
-
5.8.1.1 Clear Platform Size Recommendation
on wheeled mobility devices shown in the table below.4 Table 5.8.1.1 Wheelbase Measurements on Wheeled Mobility Devices Table !...
-
§382.55(a)
In addition, passengers at foreign airports, including those with disabilities, may be subject to security screening measures required by law of the country in which the airport is located...
-
Issue 5: Can a new chapter be written with a structure for PBS P100 that is performance based and does not disaggregate lighting design by professional disciplines (i.e., integrates subject matter in Chapters 2, 3, 5, and 6)?
Comments by [Participants]: Criteria should be based on measurable psychosocial and psychophysiological metrics (i.e., parameters and values)....
-
1(2)(b)(ii)
vehicular or pedestrian arrival points within 50 feet of the planned entrance, the unusual characteristics result in a difference in finished grade elevation exceeding 30 inches and 10 percent measured...
-
1002.4.4.1 Width and Length
Wheelchair spaces shall provide a clear width of 30 inches (760 mm) minimum and a clear length of 48 inches (1220 mm) minimum measured to 9 inches (230 mm) minimum above the floor surface...
-
1132A.3, Item 5
A pair of doors, manual or automatic, must have at least one leaf which provides a clear width of not less than 32 inches (813 mm), measured with the door positioned at an angle of 90 degrees...
-
1134A.6, Item 1.3
1.3 Other shower stall configurations shall measure at least 36 inches deep by 60 inches wide (914 mm by 1524 mm) with an entrance opening of at least 36 inches (914 mm) when a wall is...
-
§35.130(f)
(f) A public entity may not place a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures, such as the provision...
-
Grade
Grade—The difference in elevation of a section of an outdoor recreation access route, trail, or beach access route measured parallel to the predominant direction of travel....
-
4.13.10* Door Closers
then the sweep period of the closer shall be adjusted so that from an open position of 70 degrees, the door will take at least 3 seconds to move to a point 3 in (75 mm) from the latch, measured...
-
R305.1.2 Dome Spacing
The truncated domes shall have a center-to-center spacing of 41 mm (1.6 in) minimum and 61 mm (2.4 in) maximum, and a base-to-base spacing of 17 mm (0.65 in) minimum, measured between the...
-
4.13.10* DOOR CLOSERS
then the sweep period of the closer shall be adjusted so that from an open position of 70 degrees, the door will take at least 3 seconds to move to a point 3 in (75 mm) from the latch, measured...
-
Cross Slope
The difference in elevation from edge to edge of an ORAR, trail, or beach access route measured perpendicular to the direction of travel. ...
-
Detail View – Accessible Round Set-Up
Measure from the back of one chair to the back of the chair directly behind it. Chairs must be set with the front edge of the chair at the edge of the table....
-
Running Slope (Grade)
The difference in elevation of a section of an ORAR, trail, or beach access route measured parallel to the predominant direction of travel. ...
-
2.4.1
2.4.1 Based on the methods for measuring compliance, define what remedial actions are acceptable when construction elements exceed tolerances....
-
Laser scanners
These types of instruments could be used to measure floor flatness and level but they are very expensive, require training, and give accuracies in excess of what is needed for accessible...
-
1132A.3, Item 5
A pair of doors, manual or automatic, must have at least one leaf which provides a clear width of not less than 32 inches (813 mm), measured with the door positioned at an angle of 90 degrees...
-
1134A.6, Item 1.3
Other shower stall configurations shall measure at least 36 inches deep by 60 inches wide (914 mm by 1524 mm) with an entrance opening of at least 36 inches (914 mm) when a wall is installed...
-
§ 35.130(f)
(f) A public entity may not place a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures, such as the provision...