Cross slope is the slope of the surface perpendicular to the direction of travel....
Search Results "Fire-Building Surface"
-
11B-405.3 Cross slope
-
Cargill, Incorporated SafeLane® Surface Overlay CA-48
SafeLane® Surface Overlay CA-48 Commercial contractors, property managers and other private winter maintenance service providers require the same anti-skid, anti-icing and infrastructure...
-
907.2.1.2 Emergency power
Emergency voice/alarm communications systems shall be provided with an approved emergency power source.
-
4.28.3(7)
(7) In general, no place in any room or space required to have a visual signal appliance shall be more than 50 ft (15 m) from the signal (in the horizontal plane). In large rooms and...
-
4.28.3(8)
(8) No place in common corridors or hallways in which visual alarm signalling appliances are required shall be more than 50 ft (15 m) from the signal.
-
A4.28.3 Visual Alarms
The specifications in this section do not preclude the use of zoned or coded alarm systems.
-
4.28.3(6)
(6) The appliance shall be placed 80 in (2030 mm) above the highest floor level within the space or 6 in (152 mm) below the ceiling, whichever is lower.
-
4.28.1 GENERAL
Alarm systems required to be accessible by 4.1 shall comply with 4.28.
-
A4.28.3 VISUAL ALARMS
The specifications in this section do not preclude the use of zoned or coded alarm systems. In zoned systems, the emergency exit lights in an area will flash whenever an audible...
-
1.1.3 Scope
this code shall apply to the construction, alteration, movement, enlargement, replacement, repair, equipment, use and occupancy, location, maintenance, removal and demolition of every building...
-
1009.12 Alarms/emergency warning systems/accessibility
Emergency warning systems as part of the fire alarm system shall be designed and installed in accordance with NFPA 72 as amended in Chapter 35....
-
1009.12 Alarms/emergency warning systems/accessibility
Emergency warning systems as part of the fire-alarm system shall be designed and installed in accordance with NFPA 72 as amended in Chapter 35....
-
1014.3 Floor
This section requires the floor surface within camp shelters to be firm and stable and to slope not steeper than 1:48 in any direction....
-
Installation of Test Surfaces
Installation of Test Surfaces In accordance with standard EWF design and construction practice (Figure 2), the full depth surfaces were prepared to the same requirements needed for permanent...
-
Installation of Aggregate Surfaces at Bradford Woods
Installation of Aggregate Surfaces at Bradford Woods The installation of the aggregate surfaces at Bradford Woods conformed to the following protocol: Prior to installing the crushed...
-
A4.5.1 GENERAL
Wheelchairs can be propelled most easily on surfaces that are hard, stable, and regular....
-
1007.12 Alarms/emergency warning systems/accessibility
Emergency warning systems as part of the fire alarm system shall be designed and installed in accordance with NFPA 72 as amended in Chapter 35....
-
11B-305.2 Floor or ground surfaces
Floor or ground surfaces of a clear floor or ground space shall comply with Section 11B-302....
-
R302.7 Surfaces
R302.7 Surfaces....
-
M301.2 Transfer Surface (Section-by-Section Analysis)
This is an introductory section.
-
1.9.1 Division of the State Architect - Access Compliance.
Additions, alterations and structural repairs in all buildings and facilities shall comply with these provisions for new buildings, except as otherwise provided and specified herein....
-
1.9.1 Division of the State Architect - Access Compliance.
Additions, alterations and structural repairs in all buildings and facilities shall comply with these provisions for new buildings, except as otherwise provided and specified herein....
-
[2010 ADAS] 105.2.4 ICC/IBC
International Building Code, 2000 Edition (see 207.1, 207.2, 216.4.2, 216.4.3, and 1005.2.1). International Building Code, 2001 Supplement (see 207.1 and 207.2)....
-
Choice of Option One for Defining ‘‘Designed and Constructed for First Occupancy’’ (Preamble, Section-by-Section Analysis)
Option One for Defining ‘‘Designed and Constructed for First Occupancy’’ Under the option the Department has chosen for determining applicability of the new construction standards, a building...
