Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
Search Results "State Access Code"
-
E101.3 Conventional Industry Tolerances
-
C101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
-
M101.4 Dimensions
Dimensions that are not stated as "maximum" or "minimum" are absolute....
-
M101.4 Dimensions
Dimensions that are not stated as “maximum” or “minimum” are absolute....
-
§ 37.145(d)
(d) The State shall develop comments to on each plan, responding to the following points:...
-
DIVISION 2: SCOPE AND ADMINISTRATION
Note: Sections adopted or amended by state agencies are specifically indicated by an agency banner....
-
DIVISION II: SCOPE AND ADMINISTRATION
Note: Sections adopted or amended by state agencies are specifically indicated by an agency banner....
-
Introduction
Successful accessibility is often measured in inches, so attention to detail can make the difference between achieving access and excluding or injuring someone....
-
ASME
ASME serves this wide-ranging technical community through quality programs in continuing education, training and professional development, codes and standards, research, conferences and...
-
Trail Study Sites
An Access Board solicitation for potential playground study sites yielded numerous responses for trail work as well....
-
11B-604.5.2 Rear wall
ETA Editor's Note The Office of Statewide Health Planning and Development (OSHPD), which has jurisdiction over hospitals and long-term care facilities in California, issued Code Application...
-
11B-604.5.2 Rear wall
ETA Editor's Note The Office of Statewide Health Planning and Development (OSHPD), which has jurisdiction over hospitals and long-term care facilities in California, issued Code Application...
-
SDC EMLock® Magnetic Lock
Compatible with any access control system, SDC 1500 series Magnetic door locks meet the demands of security professionals, and the most rigorous building and fire life safety codes in the...
-
SDC Z7500 HiTower Pro Series Actuator Controlled Locksets
SDC HiTower® locksets comply with all national and regional building codes for locking interior office, elevator lobby, exit and stairwell fire rated doors, where the use of electric strikes...
-
1.6.15 Recipient.
Any State, territory, possession, the District of Columbia, or Puerto Rico, or any political subdivision thereof, or instrumentality thereof, any public or private agency, institution, organization...
-
102 Dimensions for Adults and Children
102 Dimensions for Adults and Children Section 2.1 of the 1991 Standards stated that the specifications were based upon adult dimensions and anthropometrics....
-
About the Author
Scott earned a bachelor’s degree in civil and environmental engineering from the Uni-versity of Wisconsin at Madison and a master’s degree in civil engineering from Montana State University...
-
12201(b) Relationship to other laws
(b) Relationship to other laws Nothing in this chapter shall be construed to invalidate or limit the remedies, rights, and procedures of any Federal law or law of any State or political...
-
§ 36.406(a)(1)
alterations subject to §§ 36.401 or 36.402 shall comply with the 1991 Standards if the date when the last application for a building permit or permit extension is certified to be complete by a State...
-
Appendix A to Part 35
Appendix A to Part 35 -- Preamble to Regulation on Nondiscrimination on the Basis of Disability in State and Local Government Services (Published July 26, 1991) NOTE: For the convenience...
-
§ 36.406(a)(3)
alterations subject to §§ 36.401 or 36.402 shall comply with the 2010 Standards if the date when the last application for a building permit or permit extension is certified to be complete by a State...
-
Q3. Are emotional support, therapy, comfort, or companion animals considered service animals under the ADA?
However, some State or local governments have laws that allow people to take emotional support animals into public places. ...
-
2.1.1
2.1.1 Clearly state the required installed tolerances for critical construction elements....
-
M101.5 Dimensions
Dimensions that are not stated as “maximum” or “minimum” are absolute....
