The facility can accommodate the miniature horse’s type, size, and weight. The miniature horse does not compromises legitimate, necessary safety requirements....
Search Results "Bench Size"
Filters
Commonly Searched Documents
-
Miniature Horses
-
Producing Printed Material in Large Print
Large print material can be produced by using a photo copier or a computer where an 18-point type size or larger can be selected....
-
11B-410.8 Restriction sign
This section includes requirements which address platform size and gate configurations for lifts with 90-degree egress, and additionally requires signs posted at the landings as follows:...
-
Re: Service Counters
Providing the full 2'6'' depth at the lower counter would provide an equal sized counter but I could argue that 18'' deep would also work....
-
B. Notice of the ADA’s Provisions
Regardless of Size, the ADA Notice Requirement Applies The ADA notice requirement applies to ALL state and local governments covered by title II, even localities with fewer than 50 employees...
-
608.2.2 Standard Roll-In Type Shower Compartments
Figure 608.2.2 Standard Roll-In Type Shower Compartment Size and Clearance...
-
608.2.3 Alternate Roll-In Type Shower Compartments
Note: inside finished dimensions measured at the center points of opposing sides Figure 608.2.3 Alternate Roll-In Type Shower Compartment Size and Clearance...
-
Approach, Enter, and Exit
This applies to all employee work areas except employee works areas that meet the elevation, size, and function requirements identified in TAS 203.9....
-
608.2.2.1 Clearance
Figure 608.2.2 Standard Roll-In Type Shower Compartment Size and Clearance...
-
604.8.1.6 Lavatory
In new construction, the wheelchair accessible toilet compartment shall contain an accessible lavatory within it, which must be at least 19 inches wide by 17 inches deep, nominal size, and...
-
10.2.1(3)
Signs that are sized to the maximum dimensions permitted under legitimate local, state or federal regulations or ordinances shall be considered in compliance with 4.30.2 and 4.30.3 for purposes...
-
R103 Conventions (Section-by-Section Analysis)
Where the required size or dimension of a facility or element is based on ratios or percentages, rounding down for values less than one half is permitted....
-
4.8.4 LANDINGS
(3) If ramps change direction at landings, the minimum landing size shall be 60 in by 60 in (1525 mm by 1525 mm)....
-
Job Accommodation Network
It soon expands to serve private employers of all sizes, government agencies, employee representatives and service providers, as well as people with disabilities and their families....
-
Are employee restrooms and break rooms required to be accessible?
Also, circulation paths must be accessible in work areas at least 1,000 square feet in size....
-
Van Space: Wider Parking Space
Van Space: Wider Parking Space Recommendation: Sizing all accessible spaces (or access aisles) for van accessibility provides greater convenience and helps ensure that van...
-
Error/Omission: Landing areas where ramps change direction (e.g., switchbacks or 90° turns) are too small.
Requirement: 4.8.4* (3) If ramps change direction at landings, the minimum landing size shall be 60 in by 60 in (1525 mm by 1525 mm)....
-
Pilot Rock PQT3-4 Square Pedestal Table Using Recycled Plastic
Specifications: Model PQT3-4 Picnic Tables have a 48" square top with 3 bench seats. Table offers 32" table height, 20" seat height (nominal dimensions)....
-
Pilot Rock PQT3-4 Square Pedestal Table Using Lumber
Specifications: Model PQT3-4 Picnic Tables have a 48" square top with 3 bench seats. Table offers 32" table height, 20" seat height (nominal dimensions)....
-
11B-226.1 General
With respect to work surfaces, this means that employers may need to procure or adjust work stations such as desks, laboratory and work benches, fume hoods, reception counters, teller windows...
-
11B-226.1 General
With respect to work surfaces, this means that employers may need to procure or adjust work stations such as desks, laboratory and work benches, fume hoods, reception counters, teller windows...
-
11B-226.1 General
With respect to work surfaces, this means that employers may need to procure or adjust work stations such as desks, laboratory and work benches, fume hoods, reception counters, teller windows...
-
11B-216.11 Check-out aisles
The referenced CBC identification signage requirements are more definitive regarding sign size and placement....
-
810.6.3 Station Names
The number of signs necessary may be directly related to the size of the lettering displayed on the sign....
