The Department is issuing guidance on counting missed/denied trips, and the Federal Transit Administration can work further with transit providers on appropriate statistical measures....
Search Results "Work Area Equipment"
2010 ADA Definition
Work Area Equipment: Any machine, instrument, engine, motor, pump, conveyor, or other apparatus used to perform work. As used in this document, this term shall apply only to equipment that is permanently installed or built-in in employee work areas. Work area equipment does not include passenger elevators and other accessible means of vertical transportation.
-
DOT Response
-
Q27. What does under control mean? Do service animals have to be on a leash? Do they have to be quiet and not bark?
The service animal must be harnessed, leashed, or tethered while in public places unless these devices interfere with the service animal's work or the person's disability prevents use of...
-
Emergency Contacts
The phone must be unlocked and working. There are apps that will allow this information to be seen even if your device is locked (See Apps below)....
-
Documenting Exceptions
When work necessary to meet the technical requirements would directly or indirectly substantially harm the protected aspect, document the reason for the determination and then apply the...
-
7.1 Characterizing Facilities
7.1 Characterizing Facilities Recommendations regarding installers of ALS can be facilitated by characterizing the nature of the venues they work in....
-
Recommendations for Buffet Meals
Buffet meals can work for all audiences, though additional time may be required (versus seated/served meals)....
-
11B-410.1 General
The ADA and other Federal civil rights laws require that accessible features be maintained in working order so that they are accessible to and usable by those people they are intended to...
-
11B-410.1 General
The ADA and other Federal civil rights laws require that accessible features be maintained in working order so that they are accessible to and usable by those people they are intended to...
-
11B-104.1.1 Construction and manufacturing tolerances
Recognized tolerances are not intended to apply to design work. It is good practice when specifying dimensions to avoid specifying a tolerance where dimensions are absolute....
-
11B-104.1.1 Construction and manufacturing tolerances
Recognized tolerances are not intended to apply to design work. It is good practice when specifying dimensions to avoid specifying a tolerance where dimensions are absolute....
-
11B-1009.2.1 Pool lift location
Where multiple pool lift locations are provided, no more than one pool lift shall be required to be located in an area where the water level is 48 inches (1219 mm) maximum....
-
F209.2.2 Bus Loading Zones
In bus loading zones restricted to use by designated or specified public transportation vehicles, each bus bay, bus stop, or other area designated for lift or ramp deployment shall comply...
-
11B-224.1.1 Alterations
rooms are added as a result of subsequent alterations, compliance with 224.5 (Dispersion) is more likely to be achieved if all of the accessible guest rooms are not provided in the same area...
-
SEAT HEIGHT MEASUREMENT DETAIL
Note that examination tables and chairs only use bolsters on certain areas of the transfer surface....
-
Camping and Picnic Facilities [F244.2.3.1, F244.3, F245.2.5.1, and F244.5.3]
Where outdoor constructed features are provided in common use and public use areas that serve camping and picnic units with mobility features, at least 20 percent, but no less than one,...
-
1.3.2 Focus Following NPRM Comments
This review identified four major issue areas for the MDE Advisory Committee to address, as follows: Transfer surface height and size Permitted obstructions to the transfer surface...
-
F. Eligibility for Admission to Secondary Vocational Education Centers Based on Numerical Limits Imposed on Sending Schools
system for admission to a secondary vocational education center or program that limits admission to a fixed number of students from each sending school included in the center's service area...
-
709.5 Openings
opposite swinging doors without a center mullion shall be installed having vision panels with approved fire-resistance-rated glazing materials in approved fire-resistance-rated frames, the area...
-
3. EXCLUSIONS
Facilities obtained in emergencies such as natural disasters or in an area where contingency operations are being conducted....
-
Service animals.
It appears, therefore, that many covered entities are confused about their obligations under the ADA in this area. ...
-
Carry Information and Useful Documentation
Attaching a laminated set of brief instructions to a wheelchair itself may also be a good idea in the event that your wheelchair is disassembled or reassembled in a secure area to which...
-
How come some passengers with service animals avoid the bulkhead row?
ANSWER: It is DOT’s understanding that some service animals are trained to curl up underneath a non-bulkhead row airline seat, whereas other service animals are more comfortable in the area...