Dining surfaces and work surfaces required to comply with 902 shall be dispersed throughout the space or facility containing dining surfaces and work surfaces....
Search Results "Surface Material"
-
226.2 Dispersion
-
F226.2 Dispersion
Dining surfaces and work surfaces required to comply with 902 shall be dispersed throughout the space or facility containing dining surfaces and work surfaces. [ECTCR UFAS 5.1]...
-
5.2.2.1 Transfer Surface Width
5.2.2.1 Transfer Surface Width. The transfer surface should be 21 inches wide minimum for examination chairs and other equipment used by patients in a seated position....
-
Mats
they meet the pile height and trim requirements for fixed carpeting, have firm tapered edges for smooth transitions, be firm enough to minimize buckling or rolling and have an underside material...
-
Inpro Corporation IPC® Designer Kickplates
Features & Benefits Add a decorative touch with designer kickplates in two styles while protecting doors from scratches and dents Achieve a finished look...
-
11B-902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (762 mm) maximum above the finish floor or ground.
-
11B-902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (762 mm) maximum above the finish floor or ground.
-
Development of Surface Roughness Standards for Pathways Used by Wheelchair Users: Final Report
Development of Surface Roughness Standards for Pathways Used by Wheelchair Users: Final Report December 2014 Human Engineering Research Laboratories VA Pittsburgh Healthcare System...
-
Mirror Height
The guidelines specify that accessible mirrors be mounted so that the bottom edge of the reflecting surface is no higher than 40 inches (603.3)....
-
Maintenance
At least three EWF sites had improved SDS where the surface material was observed as more level and better compacted than previous site visits. ...
-
National Trail Surfaces Study Final Report
National Trail Surface Study Final Report February 2014 Staff Liaison Bill Botten U.S....
-
11B-606.5 Exposed pipes and surfaces
There shall be no sharp or abrasive surfaces under lavatories and sinks....
-
11B-606.5 Exposed pipes and surfaces
There shall be no sharp or abrasive surfaces under lavatories and sinks....
-
Inpro Corporation JointMaster® AR Series Seal Expansion Joint Systems
, and chemicals Heat weldable for watertight seams Industry unique design creates crisp sightline and incorporates ribs on side faces to aid in pooling epoxy and adding surface...
-
T302.1 General
Walking surfaces in non-rail vehicles shall comply with T302. EXCEPTION: Walking surfaces on lifts shall not be required to comply with T302....
-
11B-804.3 Kitchen work surface
In residential dwelling units required to comply with Section 11B-809, at least one 30 inches (762 mm) wide minimum section of counter shall provide a kitchen work surface that complies...
-
11B-804.3 Kitchen work surface
In residential dwelling units required to comply with Section 11B-809, at least one 30 inches (762 mm) wide minimum section of counter shall provide a kitchen work surface that complies...
-
1016.2 Surface
The surface of outdoor recreation access routes, passing spaces, and resting intervals shall be firm and stable....
-
1016.2 Surface
The surface of outdoor recreation access routes, passing spaces, and resting intervals shall be firm and stable....
-
1016.2 Surface
This section requires the surface of outdoor recreation access routes, passing spaces, and resting intervals to be firm and stable....
-
Tile Tech Pavers® Traver-Pave™
Travertine is a beautiful, timeless natural stone that conveys warmth and elegance in any setting and have been used architecturally around the world for thousands of years. However...
-
U.S. Tape Company, Inc. Digi-Pro
Description The DIGI-PRO is a 12.5" diameter measuring wheel with a digital counter that converts your measurements into 8 different...
-
Tiles
TIL was the most expensive of the five types of surfaces identified for study. ...
-
11B-408.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Sections 11B-302 and 11B-303....
