5.4.6 Transfer Support Gripping Surface Cross Section and Clearances for M301, M302, and M305.2 Description: This provision prescribes a cross-sectional profile of the transfer support...
Search Results "Cross-Aisle"
-
5.4.6 Transfer Support Gripping Surface Cross Section and Clearances for M301, M302, and M305.2
-
Flange way gap
For rail projects, no flange way gap can be greater than 2.5" where passenger circulation paths cross tracks at grade (i.e. a street-level pedestrian crossing over streetcar tracks)....
-
Common Problems with Parking
Ø There are no access aisles, or access aisles are too narrow. Ø There are built-up curb ramps in access aisles....
-
General: ADA Standard Section 307.1
Section 307.1 of the ADA Standards covers information in the current ADA Standards for protruding objects.
-
Protruding Objects: ADA Standard Section 204
Section 204 covers the scoping requirements of general exceptions for protruding objects in the most current ADA Standards
-
Protruding Objects: ADA Standard Section 307
Section 307 covers the current ADA Standards for protruding objects.
-
11B-204 Protruding objects
[See subsections ...]
-
11B-307.1 General
Protruding objects shall comply with Section 11B-307.
-
11B-307 Protruding objects
[See subsections ...]
-
11B-307 Protruding objects
[See subsections ...]
-
11B-307.1 General
Protruding objects shall comply with Section 11B-307.
-
11B-204 Protruding objects
[See subsections ...]
-
1013.2 Where required
1013.2 Where required. Guards shall be located along open-sided walking surfaces, including mezzanines, equipment platforms, stairs, ramps and landings that are located more than 30...
-
Accessible Passenger Loading Zones [§503]
Accessible Passenger Loading Zones [§503] Requirements for accessible passenger loading zones address vehicle pull-up spaces and access aisles, including their dimensions, surfacing,...
-
Parking
Parking areas may lack accessible parking spaces with adequate access aisles and signs, or may be on a sloped surface....
-
5.4.6 Transfer Support Gripping Surface Cross Section for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.6 Transfer Support Gripping Surface Cross Section for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
503.5 Vertical Clearance
Vehicle pull-up spaces, access aisles serving them, and a vehicular route from an entrance to the passenger loading zone, and from the passenger loading zone to a vehicular exit shall provide...
-
B. Information about the Aircraft
following: Any limitations concerning the ability of the aircraft to accommodate an individual with a disability; The location of seats, if any, in a row with a movable aisle...
-
A. Background
This Chapter discusses the ADA requirements for curb ramps at pedestrian crossings that are currently enforced by the Division under PCA....
-
503.5 Vertical Clearance
Vehicle pull-up spaces, access aisles serving them, and a vehicular route from an entrance to the passenger loading zone, and from the passenger loading zone to a vehicular exit shall provide...
-
503.5 Vertical Clearance
Vehicle pull-up spaces, access aisles serving them, and a vehicular route from an entrance to the passenger loading zone, and from the passenger loading zone to a vehicular exit shall provide...
-
E. Services in the Cabin
on-board wheelchair, using the on-board wheelchair to enable the passenger to move to and from the lavatory which, if requested, could entail transferring the passenger from a seat to an aisle...
-
11B-406.5.10 Diagonal curb ramps
Diagonal curb ramps with flared sides shall have a segment of curb 24 inches (610 mm) long minimum located on each side of the curb ramp and within the marked crossing....